Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

MOOG ES3571 [FRONT OUTER TIE ROD END]

This Moog brand front outer tie rod end is just what you need to ensure the safety and integrity of your vehicle's suspension and steering.

Specifications:

  • Fits either LH (Driver Side) or RH (Passenger Side) OUTER
  • Replaces one of many dealer part numbers including: 5098996AA, 52013468AB, 52013468AC, 52106710AA, 52106710AB, 52106710AC
  • Connects to inner tie rod
  • Direct replacement
  • Built to strict quality control standards

When installed correctly and an alignment performed, this outer tie rod could also reduce uneven tire wear.

Item Condition: New

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (0:47)
    • Loosen the lug nuts
    • Raise and support the vehicle
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Outer Tie Rod (1:14)
    • Soak the tie rod jam nut and the other tie rod nut in rust penetrant
    • Loosen the jam nut with a 24mm wrench
    • Remove the 21mm nut from the outer tie rod
    • Strike the wheel spindle with a hammer to release the outer tie rod
    • Pull the tie rod down out of the wheel spindle
    • Twist off the tie rod, counting how many turns it takes to remove
    • Hold the inner tie rod with locking pliers
    • Mark the jam nut position with a marker
    • Twist off the jam nut with a 24mm wrench, counting how many turns it takes to remove
  3. step : Installing the Outer Tie Rod (5:25)
    • Mark the new jam nut
    • Twist on the new jam nut the same number of turns it took to remove the old one
    • Twist on the outer tie rod the same number of turns it took to remove the old one
    • Insert the outer tie rod stud into the wheel spindle
    • Fasten the 22mm nut onto the outer tie rod
    • Tighten the 22mm nut to 63 foot-pounds of torque
    • Tighten the new jam nut with a 22mm wrench
    • Grease the tie rod fitting until the boot swells
  4. step : Installing the Wheel (7:04)
    • Lift the wheel into place
    • Start the lug nuts
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 110 foot-pounds

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Hammer
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Gloves
  • Rust Penetrant
  • Marker / Writing Utensil

  • Pliers, Cutters & misc Wrenches

  • Vise Grip Pliers
  • Side Cutters

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Sockets - Metric

  • Complete Metric Socket Set

There are no reviews for this item.
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
is the ball joint included?
Brad G February 14, 2016
This part comes as seen in the picture.
Brian F February 16, 2016
Year Make Model Description
2005-2010Chrysler 300 Chrysler 300 Outer Tie Rod Driver or Passenger Side Rear Wheel Drive MOOG ES3571
2008-2010Dodge Challenger Dodge Challenger Outer Tie Rod Driver or Passenger Side MOOG ES3571
2006-2010Dodge Charger Dodge Charger Outer Tie Rod Driver or Passenger Side Rear Wheel Drive MOOG ES3571
2000-2004Dodge Dakota Dodge Dakota 2 Wheel Drive Outer Tie Rod Driver or Passenger Side MOOG ES3571
2005-2010Dodge Dakota Dodge Dakota Outer Tie Rod Driver or Passenger Side MOOG ES3571
2000-2003Dodge Durango Dodge Durango 2 Wheel Drive Outer Tie Rod Driver or Passenger Side MOOG ES3571
2005-2008Dodge Magnum Dodge Magnum Outer Tie Rod Driver or Passenger Side Rear Wheel Drive MOOG ES3571
2006-2009Mitsubishi Raider Mitsubishi Raider Outer Tie Rod Driver or Passenger Side MOOG ES3571
Part #: 1ASTE00058

Out of Stock

MOOG
Brand #: ES3571

How-to Video:

(07:32 min)