These tie rod ends are just what you need to ensure the safety and integrity of your vehicle's suspension and steering.

Specifications:

  • Comes as a SET of 4
    • (2) - FRONT INNER Tie Rod Ends - LH (Driver Side) & RH (Passenger Side)
    • (2) - FRONT OUTER Tie Rod Ends - LH (Driver Side) & RH (Passenger Side)
  • Replaces dealer part numbers: 56820-22000, 5682022000, MR519046, MB912519
  • Direct replacements
  • Built to strict quality control standards

Remember whenever you are replacing any front end or steering components you should have your vehicle professionally aligned as soon as possible. This will ensure proper tracking and even tire wear.

Our steering and suspension components are sealed for long life and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:35)
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Outer Tie Rod (0:59)
    • Turn the wheels by hand for better access to the tie rod
    • Remove the cotter pin from the outer tie rod with pliers
    • Remove the castle nut from the tie rod with an adjustable wrench
    • Measure the distance from the inner tie rod to the end of the outer tie rod
    • Note that measurement
    • Loosen the nut that connects the outer to the inner tie rod
    • Strike the wheel knuckle with a hammer to loosen the outer tie rod
    • Lift the outer tie rod out of the wheel knuckle
    • Twist off the outer tie rod
  3. step : Removing the Inner Tie Rod (1:59)
    • Twist off the nut that connects the outer to the inner tie rod
    • Pull the small boot clamp off the inner tie rod with pliers
    • Pry off the large boot clamp with a hammer and a flat blade screwdriver
    • Pull off the boot
    • Remove the inner tie rod with a pipe wrench
  4. step : Installing the New Inner Tie Rod (2:46)
    • Twist the new inner tie rod into place
    • Put a wire tie on the large end of the boot
    • Put the boot into place
    • Tighten the wire tie
    • Push on the small boot clamp with pliers
    • Twist on the nut that connects the outer to the inner tie rod
  5. step : Reinstalling the Outer Tie Rod (3:43)
    • Twist your outer tie rod onto the inner tie rod
    • Measure the distance from the inner tie rod to the end of the outer tie rod
    • This should be the same measurement as noted in Step 2
    • Thread the nut that connects the outer to the inner tie rod
    • Push the outer tie rod into the steering knuckle
    • Fasten the castle nut onto the outer tie rod
    • Line up the castle nut with the cotter pin hole
    • Push the cotter pin into place
    • Twist the cotter pin into place with pliers
    • Tighten the nut that connects the outer to the inner tie rod
    • Fill the outer tie rod bearing with bearing grease, using a grease gun
  6. step : Reattaching the Wheel (4:56)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds of torque in a crossing or star pattern

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Hammer
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Bearing Grease
  • Wire Ties

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers
  • Pipe Wrench
  • Adjustable Wrench

  • Ratchets & Related

  • Torque Wrench

  • Specialty Tools

  • Grease Gun

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
1
0
0
0
0
Great servise
I have had great servise with A1 auto, everything is easy to find on there page, they have a fast free shipping, a very low comparison in price to most every one else, and to say the least, i actualy got the right parts. Thanks to the guys at A1 auto!
May 16, 2018
Purchased
1 month ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2001-2005 Chrysler Sebring Coupe Front Inner & Outer Tie Rod 4 Piece Set
  • 2001-2005 Dodge Stratus Coupe Front Inner & Outer Tie Rod 4 Piece Set
  • 2000-2005 Mitsubishi Eclipse Front Inner & Outer Tie Rod 4 Piece Set
  • 1999-2003 Mitsubishi Galant Front Inner & Outer Tie Rod 4 Piece Set

This part replaces:

  • Moog ES2347RL
  • Moog EV457
  • OE # MR519046
Part #: 1ASFK01777

Ships Same Day for orders placed by 4 P.M. ET

How-to Video:

(05:28 min)