Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

These inner tie rod assemblies are just what you need to ensure the safety and integrity of your vehicle's suspension and steering.

Specifications:

  • Comes as a SET OF 4
    • Fits both LH (Driver Side) & RH (Passenger Side) FRONT INNER & OUTER
  • Replaces dealer part numbers: 68028831AB, 52013468AC, 52106710AC
  • Direct replacements
  • Built to strict quality control standards
  • Fit RWD (Rear Wheel Drive) Models only
    • Do NOT fit AWD (All Wheel Drive) Models

Remember whenever you are replacing any front end or steering components you should have your vehicle professionally aligned as soon as possible. This will ensure proper tracking and even tire wear.

Our steering and suspension components are sealed for long life and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Part Details

  • Front or Rear Location: Front

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (0:52)
    • Loosen the lug nuts
    • Raise and support the vehicle
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Outer Tie Rod (1:20)
    • Soak the tie rod jam nut and the other tie rod nut in rust penetrant
    • Loosen the jam nut with a 24mm wrench
    • Remove the 21mm nut from the outer tie rod
    • Strike the wheel spindle with a hammer to release the outer tie rod
    • Pull the tie rod down out of the wheel spindle
    • Twist off the tie rod, counting how many turns it takes to remove
    • Hold the inner tie rod with locking pliers
    • Mark the jam nut position with a marker
    • Twist off the jam nut with a 24mm wrench, counting how many turns it takes to remove
  3. step : Removing the Inner Tie Rod Boot (4:05)
    • Remove the two tie rod boot clamps with side cutters
    • Pull the boot off the inner tie rod
  4. step : Removing the Inner Tie Rod (4:50)
    • Twist the inner tie rod off the steering rack with a pipe wrench
  5. step : Installing the Inner Tie Rod (8:41)
    • Remove the travel limiter form the old inner tie rod
    • Put the travel limiter onto the new inner tie rod
    • Twist the inner tie rod onto the steering rack by hand
    • Tighten the inner tie rod with the pipe wrench
    • Remove the new jam nut from the inner tie rod
  6. step : Installing the Inner Tie Rod Boot (9:24)
    • Put the boot clamp on the steering rack side of the inner tie rod
    • Slide the boot onto the tie rod
    • Tighten the boot clamp
    • Pinch the wheel side boot clamp together with pliers
    • Slide the clamp onto the boot
    • Tighten the boot clamp
  7. step : Installing the Outer Tie Rod (10:36)
    • Mark the new jam nut
    • Twist on the new jam nut the same number of turns it took to remove the old one
    • Twist on the outer tie rod the same number of turns it took to remove the old one
    • Insert the outer tie rod stud into the wheel spindle
    • Fasten the 22mm nut onto the outer tie rod
    • Tighten the 22mm nut to 63 foot-pounds of torque
    • Tighten the new jam nut with a 22mm wrench
    • Grease the tie rod fitting until the boot swells
  8. step : Installing the Wheel (12:14)
    • Lift the wheel into place
    • Start the lug nuts
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 110 foot-pounds

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Hammer
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Safety Glasses
  • Gloves
  • Marker / Writing Utensil

  • Pliers, Cutters & misc Wrenches

  • Pipe Wrench
  • Vise Grip Pliers
  • Side Cutters
  • Slip-Joint Pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Sockets - Metric

  • Complete Metric Socket Set

  • Wrenches - Metric

  • 24mm Wrench
  • 21mm wrench
  • 22mm Wrench
  • 20mm Wrench

4.75/ 5.0
4 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
3
1
0
0
0
Good price quick service
First time ordering from here , very happy with the service will order again
June 28, 2017
As ordered
Exact fit. No problem installation. Guys at the shop had no problem with alignment either.
August 4, 2017
Big G in KC great parts awesome price
Got quotes for $400 and $200 for parts A1 got it done for under $35 ! Took the parts in got the whole job done for $240 total, after one shop wanted $470 and one nationally known shop wanted $900. 4th time using A1 they are my go to spot to get parts.
September 2, 2017
You guys are the best!!!!!
I have used you guys before and have been very pleased with not only the products Ive purchased, but how quick I have received them. I like the idea of your on line videos to help me see how to install what I bought. I have purchased parts from other places and have been very disappointed. Nowe I only buy from A-ONE AUTO. THANKS
April 6, 2018
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
2005-2010Chrysler 300 Chrysler 300 Front Inner & Outer Tie Rod 4 Piece Set Rear Wheel Drive
2008-2010Dodge Challenger Dodge Challenger Front Inner & Outer Tie Rod 4 Piece Set
2006-2010Dodge Charger Dodge Charger Front Inner & Outer Tie Rod 4 Piece Set Rear Wheel Drive
2005-2008Dodge Magnum Dodge Magnum Front Inner & Outer Tie Rod 4 Piece Set Rear Wheel Drive
Part #: 1ASFK00735


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(12:42 min)