Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

This outer tie rod end is just what you need to ensure the safety and integrity of your vehicle's suspension and steering.

Specifications:

  • Fits LH (Driver Side) OUTER
  • Direct replacement
  • Built to strict quality control standards

NOTE: For 2002 Models, there were two different tie rod options available: 1st design (14mm thread) & 2nd design (16mm thread). This tie rod is correct for models with the 2nd design tie rods.

Remember whenever you are replacing any front end or steering components you should have your vehicle professionally aligned as soon as possible. This will ensure proper tracking and even tire wear.

Our steering and suspension components are sealed for long life and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Item Condition: New

Attention California Customers:

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (0:43)
    • Pry off the hub cap with a flat blade screwdriver
    • Loosen the 35mm hub nut with the vehicle on the ground
    • Loosen the lug nuts
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Outer Tie Rod (1:08)
    • Spray both ends of the outer tie rod with penetrating oil
    • Measure from the either end of the outer tie rod
    • Place a 26mm wrench on the larger nut
    • Place a 22mm wrench on the smaller nut
    • Break the 22mm nut free
    • Straighten the cotter pin with pliers and pull it through
    • Remove the nut with a 21mm socket from the wheel knuckle
    • Hit the wheel knuckle with a hammer
    • Twist off the outer tie rod
    • Remove the 22mm nut off the outer tie rod
  3. step : Installing the New Outer Tie Rod (3:08)
    • Mark where the 22mm nut was located on the old tie rod to the new tie rod
    • Screw on the nut
    • Twist the outer tie rod into place
    • Push the outer tie rod into the wheel knuckle
    • Measure and check the outer tie rod distance
    • Tighten the 21mm nut on the wheel knuckle
    • Insert and twist the cotter pin with a pair of pliers
    • Tighten the two nuts on the outer tie rod
  4. step : Reattaching the Wheel (4:33)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the hub nut
    • Torque the lug nuts to 100 ft/lbs in a crossing or star pattern
    • Torque the hub nut to 103 ft/lbs
    • Reattach the center cap

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Measuring Tape
  • Hammer
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 19mm Socket
  • 21mm Socket

  • Wrenches - Metric

  • 26mm Wrench
  • 22mm Wrench
  • 10mm Wrench

5.00/ 5.0
1review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
0
0
0
0
Great product as usual
Great price, shipped fast, fit perfectly, and awesome install video. Only thing was on the video it said would need a 22mm wrench. Ended up needing a 15/16th and also used a 10in adjustable.
July 21, 2017
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
I already purchased an outer tie rod from oreilly and apparently they do not come with the nut that snugs against the inner tie rod. Do you sell that nut or could tell me what size it is because nobody seems to carry it? Oreilly called all around and i did the same to bo luck. Thanks
Chris S April 20, 2017
We do not offer this nut. You may need to search through an affiliated dealership parts website to find an OEM number, which may be used to cross reference for a better cost option.
Alex P April 20, 2017
Year Make Model Description
2004-2007Buick Rainier Buick Rainier Front Outer Tie Rod Driver Side
2003-2006Chevy SSR Chevy SSR Front Outer Tie Rod Driver Side
2002Chevy Trailblazer Chevy Trailblazer Front Outer Tie Rod Driver Side for Models with 16mm Thread Tie Rods
2003-2009Chevy Trailblazer Chevy Trailblazer Front Outer Tie Rod Driver Side
2002Chevy Trailblazer EXT Chevy Trailblazer EXT Front Outer Tie Rod Driver Side for Models with 16mm Thread Tie Rods
2003-2006Chevy Trailblazer EXT Chevy Trailblazer EXT Front Outer Tie Rod Driver Side
2002GMC Envoy GMC Envoy Front Outer Tie Rod Driver Side for Models with 16mm Thread Tie Rods
2003-2009GMC Envoy GMC Envoy Front Outer Tie Rod Driver Side
2002GMC Envoy XL GMC Envoy XL Front Outer Tie Rod Driver Side for Models with 16mm Thread Tie Rods
2003-2006GMC Envoy XL GMC Envoy XL Front Outer Tie Rod Driver Side
2004-2005GMC Envoy XUV GMC Envoy XUV Front Outer Tie Rod Driver Side
2003-2008Isuzu Ascender Isuzu Ascender Front Outer Tie Rod Driver Side
2002Oldsmobile Bravada Olds Bravada Front Outer Tie Rod Driver Side for Models with 16mm Thread Tie Rods
2003-2004Oldsmobile Bravada Olds Bravada Front Outer Tie Rod Driver Side
2005-2009Saab 9-7X Saab 9-7X Front Outer Tie Rod Driver Side
Part #: 1ASFK02025


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(05:20 min)