Replaces

Throttle Body Assembly Mopar 53032801AC - MPTBA00003

Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

Specifications:

  • Brand New Mopar Throttle Body Assembly
  • Original equipment part
  • Direct replacement
  • Built to strict quality control standards

Returns Note:

Our electrical and electronic parts are subject to strict quality control testing.  Once the item has been installed or plugged in, it is no longer eligible for a refund.  The item may be eligible for replacement, only if it is found to have a manufacturing defect. Before purchasing, please ensure proper diagnosis of the failed original part is performed.

OEM Part

Genuine original equipment part (OEM) that was factory installed on your vehicle by the manufacturer.

Item Condition: New

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Disconnecting the Battery (0:39)
    • Disconnect the negative battery terminal with a 10mm wrench
  2. step : Removing the Air Intake (0:45)
    • Release the clips and open the air filter housing box
    • List the air filter housing box cover up and off
    • Release the PCV hose
    • Loosen the rear clamp on the inlet pipe
    • Remove the box cover and pipe
    • Lift the bottom of the air filter housing box up and out
    • Remove the 10mm bolt behind the alternator
    • Remove the 10mm bolt behind the oil cap
    • Lift the air box up
    • Disconnect the intake sensor
    • Remove the air box
  3. step : Removing the Throttle Body (2:00)
    • Disconnect the throttle body connector by pulling back the red safety clip
    • Remove the 8mm bolts securing the throttle body to the intake manifold
    • Remove the throttle body gasket with a pick
    • Clean the gasket off and inspect it for cracks or rips
  4. step : Installing the Throttle Body (5:20)
    • Check and clean the intake manifold of debris
    • Firmly press the throttle body gasket into place
    • Insert the throttle body into place
    • Insert two alignment bolts into the top left and bottom right corner
    • Tighten the four bolts with a 3/4" drive without tightening too much to prevent breaking the manifold
    • Torque the bolts to 50 inch-pounds in a cross pattern with a 1/4" torque wrench
    • Connect the throttle body connector
  5. step : Reinstalling the Air Intake (6:54)
    • Insert the air box with the silicone gasket over the throttle body
    • Tighten the two 10mm bolts to the box
    • Connect the air temp sensor
    • Insert the air filter housing into its mounting spots
    • Insert the intake tube to the air box
    • Tighten the hose clamp
    • Connect the PCV hose
    • Lock the air filter housing box
  6. step : Reconnecting the Negative Battery Terminal (8:10)
    • Tighten the 10mm bolt to the negative battery terminal

Tools needed for replacement:

    General Tools

  • Pick

  • Materials, Fluids, and Supplies

  • Cloth Rags

  • Ratchets & Related

  • 3/4 Inch Drive Ratchet
  • Torque Wrench
  • Socket Extensions

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 8mm Socket
  • 10mm Socket

There are no reviews for this item.
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
Does the replacement unit come pre- programmed? I have been told to make sure if not I would have to find someone who could do it or dealer. Thank you Dan
Dan Y July 16, 2018
The unit should just be a plug and play application, but a lot of Dodge applications will require a relearn process.
Tim K July 16, 2018
This item should arrive back in stock around the 27th of this month. However, this is estimated by our vendor and is subject to change. Please feel free to add your email to the notify my list so you are informed once stock arrives, thank you.
Jessica D July 17, 2018
I dont know if its pre-programmed. I put it on and it worked, but had to take to mechanic because squirrels chewed the wires.
Margaret B July 17, 2018
Hey Dan, I was able to simply take out the old one and put in the new with no programing needed. Just be sure the gasket goes in correctly (is hard to mess it up), and snug it into place. Worked right off the bat.
Chris L July 17, 2018
Year Make Model Description
2007-2009Chrysler Aspen Chrysler Aspen Throttle Body Assembly V8 5.7L Mopar 53032801AC
2005-2009Dodge Durango Dodge Durango Throttle Body Assembly V8 5.7L Mopar 53032801AC
2005-2010Dodge Ram 1500 Truck Dodge Ram 1500 Truck Throttle Body Assembly V8 5.7L Mopar 53032801AC
2005-2010Dodge Ram 2500 Truck Dodge Ram 2500 Truck Throttle Body Assembly V8 5.7L Mopar 53032801AC
2006-2010Dodge Ram 3500 Truck Dodge Ram 3500 Truck Throttle Body Assembly V8 5.7L Mopar 53032801AC
2011-2012Ram 1500 Truck Ram 1500 Truck Throttle Body Assembly V8 5.7L Mopar 53032801AC
2011-2012Ram 2500 Truck Ram 2500 Truck Throttle Body Assembly V8 5.7L Mopar 53032801AC
2011-2012Ram 3500 Truck Ram 3500 Truck Throttle Body Assembly V8 5.7L Mopar 53032801AC
Only 3 left in stock
Part #: MPTBA00003


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

Brand #: 53032801AC

How-to Video:

(08:31 min)