These replacement sway bar links are just what you need to ensure the safety and integrity of your vehicle's suspension and steering.

Your sway bar helps your vehicle's suspension performance. The main purpose is to reduce body roll when going through a turn at speed. Although the sway bar itself is not a wearable item the end links are. Over time the ball & socket joints can wear causing loose connections, or even come apart and fall off.


  • Comes as a SET of 4
    • Fits both LH (Driver Side) & RH (Passenger Side) FRONT and REAR
  • Replaces dealer part numbers: 48820-06040, 48820-28050, 48830-06030, 48830-48010, 4882006040, 4882028050, 4883006030, 4883048010
  • Direct replacements
  • Built to strict quality control standards

If you can hear your sway bar rattling on a bumpy road it may be time to replace the end links. These links make great replacements and offer good cost savings over the dealer part.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (0:24)
    • Pry off the hub cap with a pry bar
    • Loosen the lug nuts with the vehicle on the ground
    • Raise and support the vehicle
    • Remove the lug nuts
    • Pull the wheel off the hub
  2. step : Removing the Sway Bar Link (1:15)
    • Spray rust penetrant on the upper sway bar link nut
    • Clean the upper sway bar link nut with a wire brush
    • Hold the upper sway bar link nut with a 6mm hex socket and breaker bar
    • Loosen the nut with a 17mm wrench
    • If the nut is stuck, hold the sway bar link ball joint with locking pliers if necessary
    • Remove the 17mm nut
    • If the nut remains stuck, cut the sway bar link stud with a hack saw or reciprocating saw
    • Hold the lower sway bar link ball joint with locking pliers
    • Remove the 17mm bolt from the lower sway bar link stud
    • Remove the sway bar link from the vehicle
  3. step : Installing the Sway Bar Link (7:54)
    • Hang the sway bar link where it attaches to the strut
    • Slide the sway bar link stud into sway bar
    • Start the 18mm nuts onto the sway bar link studs by hand
    • Hold the sway bar link ball joints with an 18mm wrench
    • Tighten the nuts with an 18mm socket and ratchet
    • Torque the 18mm nuts to 55 foot-pounds
  4. step : Installing the Wheel (8:52)
    • Slide the wheel onto the hub
    • Start the lug nuts by hand, with the tapered side facing the wheel
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Torque the lug nuts to 76 foot-pounds in a star pattern
    • Line up the hub cap with the valve stem
    • Push the hub cap onto the wheel

Tools needed for replacement:

    Allen Wrenches

  • 6mm Allen Wrench

  • General Tools

  • Jack Stands
  • Sawzall
  • Wire Brush
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Brake Parts Cleaner

  • Pliers, Cutters & misc Wrenches

  • Vise Grip Pliers

  • Ratchets & Related

  • Socket Extensions
  • Torque Wrench
  • Ratchet
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • 17mm Socket
  • 18mm Socket
  • 21mm Socket

  • Wrenches - Metric

  • 17mm Wrench
  • 18mm Wrench
  • 21mm wrench

3.0 / 5.0
3 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
wrong parts
Ordered 4 stabilizer links for my 2004 Camry 4 cyl, i verified with model and year on their website but received incorrect parts.
went to mechanic shop for installation but found out these are completely different links, had to buy from auto zone because my car was already on lift, anyways called 1A Auto and they told me that you are responsible for shipping cost.. unbelievable

spent 4 times extra buying from auto zone and they were telling me to ship by your own...
terrible service
October 9, 2017
9 months ago
Response from 1A Auto
We are sorry to hear that the parts were incorrect. We had issued a prepaid shipping label to your email inbox to have the parts returned.
October 9, 2017
Alex P Staff
Sway bar links
Well replaced the two front bars and everything was great. Then I went to replace the back ones and of course they were the wrong ones. Now I have to figure out how to return them without having to remove the front ones. Sucks!!!!
October 2, 2017
9 months ago
Response from 1A Auto
Thank you for leaving a review for this product! If any of the parts do not fit just give us a call at 888-844-3393, and one of our representatives can help get you set up with a refund or replacement!
October 2, 2017
Tim K Staff
Vero good
Excelente muy buenos productos estoy muy satisfecho y confirme gracias
September 4, 2017
1 year ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 1 answer
will this fit four wheel drive model?
james w on Apr 17, 2016
BEST ANSWER: This part is specific to vehicles with a particular set of options. We will need more information about your vehicle to confirm the fit. Please feel free to call our customer service department for clarification @ 888-844-3393.

Vehicle Fit

  • 2002-2003 Lexus ES300 Front & Rear Sway Bar Link 4 Piece Set
  • 2004-2006 Lexus RX330 Front & Rear Sway Bar Link 4 Piece Set
  • 2007-2009 Lexus RX350 Front & Rear Sway Bar Link 4 Piece Set
  • 2006-2008 Lexus RX400h Front & Rear Sway Bar Link 4 Piece Set
  • 2005 Toyota Avalon Front & Rear Sway Bar Link 4 Piece Set
  • 2002-2006 Toyota Camry Front & Rear Sway Bar Link 4 Piece Set
  • 2001-2003 Toyota Highlander 2 Wheel Drive Front & Rear Sway Bar Link 4 Piece Set
  • 2004-2013 Toyota Highlander Front & Rear Sway Bar Link 4 Piece Set
  • 2004-2008 Toyota Solara Front & Rear Sway Bar Link 4 Piece Set
  • 2009-2016 Toyota Venza Front & Rear Sway Bar Link 4 Piece Set

This part replaces:

  • Moog K90345
  • Moog K90344
  • OE # 48830AA010, 4883048010, 488300
  • OE # 48820-06040, 48820-28050
Part #: 1ASFK01836

How-to Video:

(10:10 min)