Front & Rear 8 Piece Suspension Kit TRQ PSA63588

Okay, friends, one of the first things we need to do is safely raise and support the vehicle so your wheel's off the ground. Once you've done that, we're gonna come right here to your center cover, use a nice little pry bar, and go ahead and pop this off. Now that we've done that, we're gonna remove all six of our 19-millimeter lug nuts and take the wheel off.

Now that we have the wheel off of here, we have a nice clear view of our sway bar link. To start removing it, it's important to see the inside center piece right there. That's a little Allen head. I'm gonna show you what tool to use in a second. But, first, what we're gonna do is we're gonna remove or at least loosen this 18-millimeter nut.

A lot of times what happens is as soon as the nut breaks free, the stud in the center starts to spin. That can be a hassle. So we're gonna use a tool that looks like this, this is just a little Allen head key. You're gonna find the size that fits right in there. Okay? Take your wrench, put it right over this. Put the Allen key right in the center, and then we're gonna go ahead and turn the Allen key clockwise, which will in turn, turn the nut counter-clockwise.

You can see that some of the thread locking stuff is coming off. That's pretty common, especially, as the stud heats up. There we are. Now we're gonna do the same to the upper one. There we are friends. Okay, friends, it's time for an install. Just make sure all the angles line up with the original. We're gonna put it through from the outside in, on the top, and then from the inside, out on the bottom. Start on both of your nuts, and then we'll bottom them out and torque them to manufacturer's specifications. Now let's tighten the sway bar link nuts to 74 foot-pounds.

All right let's get the wheel up on here. Start on all your lug nuts, bottom them out, and then we'll torque them to 103 foot-pounds. Let's torque these in a criss-cross manner. Now it's gonna be time to put on your center cover. If you were to look at the back side, you're gonna see something that looks a lot like a valve stem. Line that up with your valve stem, then just give it a nice loving bonk. Make sure it's completely secured. Take it for a road test.

Okay, friends. One of the first things we need to do to start this job is to safely raise and support the vehicle. I like to raise it directly on the frame. Once you have the wheel off the ground, we're going to remove our center cover. That exposes our 19-millimeter lug nuts. Remove them all, and then remove the wheel. Now that we have the wheel off of here, we have a clear view of our front strut. Let's start off by spraying everything that's going to need to come apart with some penetrant. Right down here, let's go ahead and get a little bit right in there for the threads.

Up along this area, go ahead and spray that bolt. And then, of course, this area up top, you're going to see right along the top of this strut tower there's two studs that come up. We're going to spray those so the nuts will come off. Right down this side too. Use your 24-millimeter socket to remove this nut. The next thing we need to do is separate this lower portion from the stud right here. To do that, you can use a punch with a hammer and try to come from this side and drive it out towards the front or, of course, if you have an air chisel like I do. So that broke free. That's perfect.

The next thing we need to do is get up top underneath the hood. So now under the hood, as you can tell, we can see the nuts on the top of those struts. We're not going to touch the center one. Do not touch that. Do this one right here and that one over there. These are 18-millimeter. Here's one nut. I'm just going to start it on there just a couple of threads. Remove the other one. All right. There's that one. Get the other one off. Let's go back into the wheel well. Let's go ahead and grab onto that. Pull it aside and then carefully drop it down and remove it from the vehicle.

Now that we have this out of the vehicle, we're going to go ahead and hold onto the bolt side of this with our 18-millimeter and then remove the nut side also with an 18-millimeter. Now I'm going to come from the other side with my air gun here or use whatever you want to remove this, but spin it out. Go ahead and put our nut on there just a little bit so we don't damage the threads and then give it a couple of loving bonks. That's moving right along. Take it right out. Something that we want to pay attention to before we go too much further is the orientation of this piece right here.

If you were to look at it, you're going to see it would run directly along here, and it's going to line up with one of the studs. It doesn't matter which one, just make sure it does line up when you come time to install. Now it's going to be time to go ahead and try to get this off of here. Something to pay attention to is the fact that we're going to have to hit it with a hammer. We're going to be trying to drive it off of the strut itself. As it starts coming off, there's also the possibility that it could come flying off and potentially hurt you.

Obviously, nobody wants you to get hurt. So I just want to mention, be careful for where this goes when it comes off. Grab your hammer or whatever you might have and go ahead and give it a couple of bonks. You might happen to notice that it just doesn't want to come off of there. If that's the case, go ahead and hit it with some more penetrant. Once you have a good amount of penetrant in there, go ahead and use a nice chisel or a punch, whatever you have that's going to be able to spread these ears a little bit.

As we spread these, something to pay attention to is you don't want to keep spreading them until the point where they start to crack or get brittle. You definitely don't want to damage this piece in any way. As I just spreaded those ears, what I saw was this started to let go. I'm going to give it a little wiggle. This is great. Just try to work that penetrant in there. So we got our new strut here. One of the first things we need to do to get this into the vehicle is, of course, get that bottom piece on there. To do that we're going to put a nice piece of wood on the floor, and we're going to turn this upside down.

I'm going to rest it just like this. Pay attention to where those studs are. Okay? Because that was important. I mentioned it before. When we go to install this, we want this arm that's coming out going in a straight line. You can see there's a dot, a dot, a stud. Try to make it a nice straight line. If you put it like this, obviously, it's going to cause an issue when it comes time to install. So we'll get it as close as possible. Now that we've got that nice and covered, let's go ahead and get this lined up straight as possible here. Oh, it looks pretty great.

Give it a couple of loving bonks. Now, as I'm doing this, you can tell the reason why I wanted to use wood on the bottom there. We've got all those studs coming down, and the last thing I want to do is mess anything up. As we bring this down, you're going to want to keep going until it bottoms out on this ridge right here. Looks like it's pretty much there. Double-check it all the way around just to make sure it's completely seated. So now let's take our unit. We're going to slide it right in, get it up into those, and then slide it on this stud down here.

Everything should line up perfectly. If it doesn't, and for some reason, you can't get it in here or you can't line up the top, obviously, the issue is right here. You just didn't line it up properly. I usually like to put a tiny bit of threadlocker on this right here, and then we'll get the nut on. We'll bottom it out. Let's go ahead and torque this to 81 foot-pounds as well. It's going to be time to put in the lower bolt for the strut here. Goes through from the inside or towards the inside of the vehicle here and then going out. Let's go ahead and bottom this out, and then we'll torque it to manufacturer's specifications.

Now we're going to torque this to 81 foot-pounds. There we are. Let's take our two upper mounting nuts. We'll get those on. We'll bottom them out, and then we'll torque them to manufacturer's specifications as well. Torque these to 33 foot-pounds. It's always a great idea to double-check everything that you removed and replaced. Just make sure everything's secure and good to go. Once you've done that, let's go ahead and get the wheel up on here. Bring the vehicle down so the tire's just barely touching the ground so it can't spin. And then torque the wheels in a criss-cross manner to 103 foot-pounds.

Now it's going to be time to get our center cover on here. If you were to turn it around, you might see something that looks a lot like a valve stem. Line it up with your valve stem, and then go ahead and pop it on there.

Okay, friends, one of the first things we need to do to start this job is to safely raise and support the vehicle. I like to raise it directly on the frame. Once you have the wheel off the ground, we're going to remove our center cover. That exposes our 19-millimeter lug nuts. Remove them all and then remove the wheel. Okay. So we took the wheel off so we have a nice, clear view of the sway bar link here. You don't necessarily have to, but it makes it easier to see. What you're going to need is a 7-millimeter Allen head. I'm going to come right in here and I'm just going to give it a couple of nice bonks. Now we're going to take our 21-millimeter wrench, put it right over this nut. The next thing we're going to do is use a ratchet or an air gun, whatever you have, put it on here. And when we turn this, we actually want to try to turn it so we're tightening. It's going to sound weird, but essentially we want the ratchet so it's tightening and the wrench so it's turning to the left. We'll break that free and then we'll go like this, and what you'll notice is it starts loosening up. Remove that completely. There we go. Do the same to the top.

Okay. I'll get my tool off of here. There we are, friends. Once you've compared the new sway bar link to your old sway bar link, it's going to be time for the install. You're going to notice your new sway bar link came with some nice new washers. Those washers are going to go on before you install. Slide them right in, and they're going to go up against this nutted area. Start it in the control arm, and then I'll put it in the sway bar. I'm just going to get this bent down. Slide it right in there. Perfect. We've got our two nuts here. Start them both on. Now it's going to be time to tighten these up. To get onto that nut that's on the inside there, use your 17-millimeter wrench. Now I'm going to use a 21-millimeter and I'm going to snug this up. All right. That bottomed out. Do the same to the other one and then we'll torque them down. Now we're going to torque these to 107 foot-pounds.

It's always a great idea to double-check everything that you removed and replaced. Just make sure everything's secure and good to go. Once you've done that, let's go ahead and get the wheel up on here. Bring the vehicle down so the tire is just barely touching the ground, so it can't spin. And then torque the wheels in a criss-cross manner to 103 foot-pounds. Now it's going to be time to get our center cover on here. If you were to turn it around, you might see something that looks a lot like a valve stem. Line it up with your valve stem and then go ahead and pop it on there.

Okay, friends, one of the first things we need to do is safely raise and support the vehicle, so your wheel's off the ground. Once you've done that, we're gonna come right here to your center cover. Use a nice little pry bar, and go ahead and pop this off. Now that we've done that, we're gonna remove all 6 of our 19-millimeter lug nuts and take the wheel off.

Now that we have the wheel off of here, we have a nice clear view of the rear shock. We're gonna start by removing this 18-millimeter bolt right here, and then we'll just start it back in just a few threads. Okay, so that's pretty good right there. It's pretty much ready to come out. At this point, let's make our way down to the bottom.

So for the next step, if you're working on a lift and you're jacking it up by the frame of the vehicle, what you're also gonna need to do is go ahead and put something underneath the differential so you can bring this up a little bit to take the pressure off the shock bolts. Now I'm gonna use my 18-millimeter wrench to hold this side of the bolt, and I'll remove this 18-millimeter nut. There it is, friends.

Okay, friends, it's time to install our new shock. One of the first things you need to do when it comes time to installing your shock is to make sure you charge it up. Let's get right down on the ground. Okay, we have our shock on the ground here, facing straight up and down. I've got it securely between my feet so it can't slide out on me. I'm gonna carefully press this down until it bottoms out, and then I'll let it completely rise up. After it's done that, I'll repeat the process another three to four times.

Okay, so we've got it all charged up. Let's go ahead and put it up into the vehicle. We're gonna grab onto these bolts. Make sure they're in decent enough condition. If the threads need to be cleaned up, go ahead and clean them up. The shorter bolt is gonna go up at the top, so we'll go ahead and start that one in, just a few threads.

Moving along to the bottom, at this point, you might notice that the holes just don't line up. If for some reason, the hole for the differential is higher than the shock, that's really not too big of a deal because you could just compress the shock slowly and meet up with the holes. If it's in the other direction, what might you have to do? Maybe you have to jack up a little bit more on the frame or maybe a little bit more on the differential to make it so it matches up. Grab your nut. Start it on there. All right, let's bottom everything out and then torque it down. Go ahead and torque those shock nuts to 59 foot-pounds. Let's do the same to the other.

All right, let's get the wheel up on here. Start on all your lug nuts, bottom them out, and then we'll torque them to 103 foot-pounds. Let's torque these in a crisis cross manner. Now it's gonna be time to put on your center cover. If you were to look at the backside, you're gonna see something that looks a lot like a valve stem. Line that up with your valve stem. Then just give it a nice loving bonk, make sure it's completely secured, take it for a road test.

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.

In this video, we're going to show you how to replace the front strut on this 2003 GMC Envoy XL. We'll show you on the passenger's side, but the driver's side is the same procedure. The items that you'll need for this include a new front strut from 1AAuto.com, 10mm, 15mm, 17mm, 18mm, and 19mm socket, a ratchet, piece of pipe for extra leverage, a 15mm and 18mm wrench, flat blade screwdriver, torque wrench, hammer, jack and jack stands, pry bar, and a 4.5mm Allen wrench. We recommend that if you replace the strut on one side, that you do it on the other side as well.

Start off by prying off your hub cap, and then just loosen out this 35mm nut. Now, loosen the lug nuts in a crossing pattern. We'll just fast-forward as Mike does this. Once you've loosened them, just jack the vehicle up, then remove the lug nuts the rest of the way. Now, the wheel will pull off.

Now, you want to remove these two 17mm bolts. You can see Mike is using an 18mm wrench to hold the nut on the inside. It will just make it easier to remove that bolt. Now, using a flat blade screwdriver, just pry out on the caliper, and then you can just set that aside. Now, pry out your brake pads. Now, you want to remove these two 18mm bolts. We'll just fast-forward as Mike does that. You can see, he's using a piece of pipe for some extra leverage to help brake those bolts free. Once those are removed, the bracket will pull right off. If your rotor doesn't slide right off then you may just want to tap it with a hammer, turn it, and then hit it again with a hammer.

Right, so if you have trouble getting the rotor off, it actually has press holes. You would get a bolt that's the proper size. I believe this is an M12 bolt. Use two bolts, thread them into those holes. As you tighten them up, they press against the hub and push the rotor off.

To get your axle out, maybe use a pry bar or some other the long item. You will put it up, in, and put it on the back of the axle right where it connects to the transmission or the axle, I should say. Make sure you're hitting the metal and it comes right out.

If you want to do the driver's side, you'll need to remove these four 15mm bolts and pull this panel down in order to access it. Using a 15mm socket, ratchet, and wrench, just remove this bolt. We'll fast-forward as Mike does that. Now, using a hammer, just hit the upper control line off the ball joint. Now, just pry open this clip and pull the harness free. You want to secure your caliper to somewhere out of the way, so we'll just wire-tie it right here on to the back end plate.

Now, you want to remove these 10mm bolts. We'll fast-forward as Mike does that. Now, just lift up on the upper control arm, pull this back, and make sure that the axle is loosened. Pull your axle the rest of the way out of the differential. You step around a little bit, and you can get it going up in. Just got to ankle it up, get it going up and in a little bit from the hub. Careful with all of your ABS wires, hoses and stuff.

Just spray this bolt right here on your sway bar link with some penetrating oil. Then, using a 15mm wrench and a 4.5mm Allen wrench (you can use some other wrench with some extra leverage on the Allen wrench), you want to just separate that nut and remove it. Next, you want loosen up these two 15 mm bolts. Just spray them with some penetrating oil. Then we'll just fast-forward as Mike loosens those up. Just push the wheel knuckle up, and then loosen those just so that they're finger tight and just a few threads on. That will hold the strut in place.

Then you want to remove this 18mm bolt right here. Using your socket, ratchet, and a piece of pipe just brake that free. Once you remove the nut, just tap out the bolt a little bit. You'll notice the brake lines in the way, so you just need to use a pry bar and pry that bolt out the rest of the way. Just lift up on the wheel knuckle, and then that will allow you to pull that out.

Spray some penetrating oil around the base of the strut, and then just hammer the wheel knuckle off with the strut. To keep the wheel knuckle from going all over the place, we're just going to wire tie it up. If you do this, you want to make sure that it's still kind of loose so you can still move the upper control arm up and down. Then remove those two 15mm nuts at the top of the strut, and just maneuver the strut down and out.

On the bottom is the old strut; above it is the new strut from 1A Auto. You can see they're identical, and they'll fit exactly the same.

Feed your new strut up into place. Then once you get the studs through, just replace those two 15mm nuts to hold it in place. Place a jack underneath the lower control arm. I've also got the lift where you have jack stands next to the vehicle. Just line up the strut and jack up the control arm into the strut. We will fast-forward as Mike tightens up that bolt. Now, just torque this bolt to 90 foot-pounds. Tighten up those two 15mm nuts and torque them to 50 foot-pounds.

We'll fast-forward as Mike replaces the nut in the sway bar. Using his 4.5 mm Allen wrench and his wrench, he's going to tighten that back up. As you're tightening up that final bit, make sure you have a wrench between the Allen wrench and the sway bar so you can still remove the Allen wrench from that bolt. Then just clip those wire ties if you ended up using them. Be careful not to hit wires. I just set it right into the hub and pull it, staying up around, and get it all the way into the hub. Then pull on it and feed it into the axle. Careful with the seal. You want to put that in, just doing a kind of back up in place that you go. Do not overextend. Just put that in place and push your axle right in and make sure it's locked.

Now, replace your brake line bracket in the two 10mm bolts to hold it into place. You want to just use the upper control arm to hold the wheel knuckle in place while you're doing this. Re-clip this harness. Now, hammer your upper control arm back down into the old one. Replace the bolt and the nut and tighten them up. You want to make sure that these holes line up in between the two holes that are on the hub. Then you just slide your rotor back into place and replace the lug nut to hold it into place. You want to check these slides on your caliper bracket and make sure they're greased up. If they're not, just apply some brake grease to them. Then fit the bracket into place. You can then just start twisting in your bolts by hand and then tighten them up.

Now, torque these two bolts to 110 foot-pounds. Torque each of these to 110 foot-pounds and then just replace your brake pads. If there's no grease on the ends, just apply some brake grease. Now, push your caliper back down into place and replace those two 17mm bolts. We'll fast-forward as Mike does that and tightens those up. Now, torque each of those to 40 foot-pounds.

Replace the hub nut. Remove the lug nut that you put on there to hold the rotor in place. Then put your wheel in place. Then replace each of the lug nuts and tighten them preliminarily. Now, torque each of these to 100 foot-pounds in a crossing pattern. Then torque the hub nut to 103 foot-pounds. Then replace your hub cap.

After you've done any work on the brakes, you want to just pump the brake pedal until it firms out. Then you want to do a stopping test from 5 miles per hour and 10 miles per hour.

We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.