Our steering and suspension components are sealed for long life and do not require the extra maintenance typically required by greasable versions.

Direct Fit

All parts are direct fit, application-specific parts with no modifications required

Rigorously Tested

Rigorously tested and made from higher quality materials than the competition. Our parts are built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

Our parts are manufactured by some of the same factories that the OEMs use.

Prepackaged for Your Convenience

Our kits have been carefully put together to include all of the parts you need to get the job done, saving you both time and money. These kits also help take the guesswork out of finding the correct part for your vehicle’s steering or suspension system, allowing you to get started on your repair project faster.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:40)
    • Loosen the lug nut covers with a 19mm socket
    • Pull off the center cap
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Sway Bar Link (1:13)
    • Turn the wheel by hand
    • Hold the nut at the top of the sway bar link with a 13mm wrench
    • Loosen the sway bar link bolt with a 13mm socket and ratchet
    • Apply penetrating oil to the bolt if necessary
    • Make note of the positions of the bushings and washers
    • Tap the bolt out with a hammer
  3. step : Installing the New Sway Bar Link (2:36)
    • Place a rubber bushing on the control arm
    • Put on a washer
    • Put on the metal sleeve
    • Lift the sway bar with a pry bar
    • Put a rubber bushing on top of the metal sleeve
    • Put a washer and a rubber bushing onto the bolt
    • Slide the bolt into place
    • Put a rubber bushing on the bolt, on top of the way bar
    • Put on a washer
    • Thread on the nut
    • Hold the nut at the top of the sway bar link with a 14mm wrench
    • Tighten the sway bar link bolt with a 14mm socket and ratchet
  4. step : Reattaching the Wheel (4:10)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
    • Reattach the center cap, lining up the notch with the valve stem
    • Tighten the lug nut covers with a 22mm socket

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Hammer
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • 13mm Socket
  • 14mm Socket
  • 19mm Socket

  • Wrenches - Metric

  • 13mm Wrench
  • 14mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2002-2007 Buick Rendezvous 4 Piece Set Suspension Kit
  • 2001-2005 Pontiac Astre 4 Piece Set Suspension Kit

This part replaces:

  • Hollander 512-01198L
  • Hollander 512-01198R
  • Hollander 512-01288R
  • Hollander 512-01289L
  • OE # 10318097
  • OE # 10318098
  • OE # 10402115
  • OE # 10413557
  • OE # 15851956
  • Dorman 521-639
  • Dorman 521-640
  • Reference Number CB91003
  • Reference Number CB91004
  • Moog K5342
  • Moog K621351
  • Moog K621352
  • Moog RK621351
  • Moog RK621352
Part #: 1ASFK05518



How-to Video:

(05:01 min)