Specifications:

  • Brand New Suspension Kit
  • Comes as a Set of 6
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacements
  • Built to strict quality control standards

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Part Details

  • Kit Includes: (2) Front Outer Tie Rods
  • Kit Includes: (2) Front Wheel Bearings
  • Quantity: 6 Piece Set
  • Kit Includes: (2) Front Inner Tie Rods

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

  1. step : Remove the wheel and tire (1:00)
    • Loosen your hub nut with your 35 mm socket.
    • Loosen your lug nut with your 19 mm lug wrench.
    • Raise and secure the vehicle.
    • Remove the lug nuts and then the wheel, remove the hub nut.
  2. step : Remove Brake Caliper (2:17)
    • Turn wheels all the way in the opposite direction of the side you are working on.
    • Use your 18 mm socket wrench to remove the caliper bolts.
    • Use a wrench to pry the caliper off.
    • Use a wire tie to help prevent stress on the caliper.
  3. step : Remove Brake Rotor (2:58)
    • Take care not to touch the disk, and if you do make sure to clean it with rubbing alcohol or mineral spirits.
  4. step : Remove Hub (3:04)
    • Remove the clips for the hub harness.
    • Use a screwdriver to unclip the hub harness.
    • Unbolt the hub harness.
    • Remove the 3 bolts securing the hub using your 18mm socket and ratchet or breaker bar.
    • You can use penetrating oil to help.
    • Remove the hub, using driving tools to help work it out of the steering knuckle.
    • Clean up any corrosion with a wire brush.
  5. step : Install new hub (6:45)
    • Use some penetrating oil to prep the knuckle for the new hub.
    • Put the three 18mm bolts in place and tighten the nuts to 65 ft lbs.
  6. step : Put brakes and wheel back on (6:45)
    • Refer to our other videos for more detailed instructions.
    • Remember to replace the lug nuts on in a star pattern.
    • Lug nuts tighten to 95 ft lbs
    • Hub nut is 75 ft lbs.
    • Make sure to check your brakes and steering before driving again.
    • Make sure to have the vehicle aligned.

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Jack Stands
  • Wire Brush

  • Materials, Fluids, and Supplies

  • Anti-Seize Grease
  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Lug Wrench

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • 10mm Socket
  • 11mm Socket
  • 12mm Socket
  • 13mm Socket
  • 14mm Socket
  • 15mm Socket
  • 16mm Socket
  • 17mm Socket
  • 18mm Socket
  • 19mm Socket
  • 35mm Socket

  • Wrenches - Metric

  • 13mm Wrench
  • 18mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
1998Chevy Blazer S10 Chevy Blazer S10 4 Wheel Drive 6 Piece Set Suspension Kit for Models with Offset Tie Rod
1999-2005Chevy Blazer S10 Chevy Blazer S10 4 Wheel Drive 6 Piece Set Suspension Kit
1998Chevy S10 Pickup Chevy S10 Pickup 4 Wheel Drive 6 Piece Set Suspension Kit for Models with Offset Tie Rod
1999-2004Chevy S10 Pickup Chevy S10 Pickup 4 Wheel Drive 6 Piece Set Suspension Kit
1998GMC Jimmy S-15 GMC Jimmy S-15 4 Wheel Drive 6 Piece Set Suspension Kit for Models with Offset Tie Rod
1999-2001GMC Jimmy S-15 GMC Jimmy S-15 4 Wheel Drive 6 Piece Set Suspension Kit
1998GMC S-15 Sonoma GMC S-15 Sonoma 4 Wheel Drive 6 Piece Set Suspension Kit for Models with Offset Tie Rod
1999-2004GMC S-15 Sonoma GMC S-15 Sonoma 4 Wheel Drive 6 Piece Set Suspension Kit
1998Isuzu Hombre Isuzu Hombre 4 Wheel Drive 6 Piece Set Suspension Kit for Models with Offset Tie Rod
1999-2000Isuzu Hombre Isuzu Hombre 4 Wheel Drive 6 Piece Set Suspension Kit
1999-2001Oldsmobile Bravada Olds Bravada 4 Wheel Drive 6 Piece Set Suspension Kit

This part replaces:

  • Moog ES3462
  • Dorman 951-011
  • Hollander 538-01459
  • OE # 12413045
  • OE # 12471301
  • OE # 12471300
  • Moog ES3584
  • Reference Number 513124
Part #: 1ASFK05094


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(07:28 min)