Replaces
This part doesn’t fit a . Select from parts that fit.
1A Auto Lifetime Warranty
Frequently bought together
Part Details
TRQ suspension kits are manufactured using premium raw materials and coatings for extended service life. Each TRQ suspension component is designed to be a direct, maintenance-free replacement to the stock unit. To extend the life of your steering and suspension components, TRQ recommends replacing components in pairs, sets, or kits. All products are fit and road-tested in our Massachusetts R&D facility to ensure we deliver on our promise of Trusted Reliable Quality.
Product Features
Our steering and suspension components are pre-greased and sealed for long life and do not require the extra maintenance typically required by greaseable versions.
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace an upper control arm on this 2002 Chevy Suburban. We show you on the passenger side, but the driver side has the same procedure. The items you'll need are a new upper control arm from 1AAuto.com, a 10mm, 21mm, and 22mm socket and ratchet, 18mm and 21mm wrench, a marker, a torque wrench, jack and jack stands, a grease gun, a hammer, and an air hammer depending on the condition of your vehicle. After completing this procedure you will need to get a professional alignment done.
Start out by removing the hubcap. You want to remove the lug nuts. If you don't have air powered tools, you'll want to do it while the vehicle is on the ground. Loosen them preliminarily, raise the vehicle, and remove the lug nuts the rest of the way. On these brackets, you'll see a tab coming through from the upper control arm. Mark where that tab is. Remove these two 10mm bolts. Next, remove this 18mm nut, and you can see Mike uses an 18mm wrench and another wrench for some extra leverage to break it free and then removes it the rest of the way with the 18mm wrench. Hit the wheel knuckle and control arm to break them free. Then remove the 21mm nuts on either side.
Jack up your wheel, and you want to do this underneath the wheel knuckle. Remove the upper control arm nut and then remove these bolts and the bracket that's on them. Our first one pulled out no problem, this one's a bit more difficult. We tried using a hammer, that doesn't work. We tried using a wrench to help break it free, but it's in there really good. If you have this same problem, we put a nut back on it and use an air hammer to knock it out. Now that those bolts are out, you want to remove the control arm up and down while pulling out and it'll pull free.
Take your new upper control arm and push it back into place. Then push the bolts in to hold it into place. You want to make sure that you have those brackets on either side and that they're lined up. Now, angle the control arm down into the wheel knuckle. Once it's pressed down into place replace that 18mm nut. We'll fast forward as Mike tightens all of those up. Replace and tighten up those two 10mm bolts. Using a grease gun put it into place on the end of your control arm and fill it up. Put the wheel back into place and then replace each wheel lug nut and tighten them up. You want to tighten them preliminarily, lower the vehicle, and then tighten them the rest of the way. Torque each lug nut in a crossing pattern to 100 foot-pounds. Replace the hubcap and tighten up those lug nut caps.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Take the center cap off. Use a straight-blade screwdriver. Use a 22-millimeter socket. Take the lug nuts off. Pull the wheel off. These bolts are pretty rusty so I'm just going to use some rust penetrant and soak those before I start. Before we take this nut off, we just want to mark this cam right here. This is for the alignment. When you go to put this back together, you want to put this in the same location so at least it's close. You're still going to need to get an alignment done afterwards, but this will get it a little bit closer. I want to get this ABS wire out of the way, our wheel speed sensor wire. Disconnect the connector up here. Just push up on that tab, slide it out and use a trim tool. Just pull up on that retainer. You can do the same over here, and right here. Sometimes these ones break, just be careful. All right. So this piece is going to break so I'm just going to disconnect it right from the arm itself. And disconnect this right here. Sometimes you can use a screwdriver and just pop that out, or a needle-nose pliers also works. You just squeeze those together. I'm just going to put some rust penetrant on this bolt right here. Let that soak a little bit. We want to take that off next. Just remove this bracket. Use a 10-millimeter socket. Remove this bolt. It's probably going to break. Yup, it broke. Well, hopefully yours doesn't break. And slide that off.
All right. Now, we're going to take this nut off using an 18-millimeter wrench. Now I'm going to leave this nut on just a couple of threads, and then we're going to break this upper ball joint free from the knuckle. I'm going to use a pickle fork to break this free. Just slide it in, in between the ball joint and the knuckle and just give it a hit. There we go. Take the pickle fork out and just push down the upper control arm a little bit. You might need a pry bar. And take the nut off and you could slide it out. And just make sure that there's not too much tension on the brake line, brake hose. I'm going to take a 21-millimeter wrench, 21-millimeter socket. Now this is old and rusty so I just had to heat up that nut to break it loose. Normally you wouldn't have to do that. And loosen it up. That nut's pretty hot right now so I'm just going to let that cool down before I take that off. Take that nut off and see if you can pry this cam off. This is just the alignment cam. Just use a pry bar and a hammer. And just pry that off. All right. This cam bolt is stuck in there pretty good so I'm just going to use some more rust penetrant, soak it down for a while.
Here we go. All right. Get that out and do the same for the other side. All right. I'm just going to take this bracket out of the way. Just use a 13-millimeter socket and you can just slide it out of the way. Don't bend it too much. Here we go. And just use a pry bar and you can pry the arm out. And take the new control arm and just line it up. You can take a rubber mallet, or a dead-blow hammer to tap it in if you need to. And get the bolt started. And take this cam and the nut. Get the nut started. Now we tighten this up. Now we want to align that mark up. What you do is take your 21-millimeter wrench and just move the bolt on this side until that lines up. And you can snug that down. And we'll do the same for the other side. All right. Now, we're going to torque this nut to 140-foot-pounds. Do the same on the front one. Take this brake hose bracket and install that. Put the bolt back in and tighten that up. Get the nut off. Put that aside. Get this lined up with the upper knuckle. And I'll use a pry bar, just pry this down. Take the nut and get the nut started.
Now, I'm going to use a 19-millimeter ratchet wrench, while I'm using the pry bar to pry it down on the ball joint. Tighten this up. All right. Now, if you have the ability, just torque this with a torque wrench, you can torque this to 37-foot-pounds. Do the best you can. And if the stud starts spinning, you can use an allen key, that's a six-millimeter hex key. But if you use the pry bar and you just pry it down, you should be able to get that without having the stud spinning. Take this brake hose bracket and line that up. Put the nut on or the bolt in and snug it up. And take the wheel speed sensor wire and reconnect that. And then we have this holder or clip. Install that. Lock that in place. Reinstall this clip and connect the connector. And push the retainer. I'm just going to find the hole where it goes. There it is. And lock that in position. And take this fitting. Install that. Snug it up with a seven-millimeter wrench.
And take a grease gun and give it a couple pumps of grease. What you can do is look at the boot as you're greasing it, once you see the boot start to move, that's good enough. And put the wheel back up. Put the lug nuts on. Now I'm going to torque these lug nuts to 140-foot-pounds in any star pattern to tighten the wheel down evenly. And just go around again, double check. Install the center cap.
Tools used
So before you do this job, you wanna keep in mind that after you're done, you're gonna have to go to an alignment shop and have the vehicle aligned so you don't burn out your tires and have premature tire wear. Now, I'm gonna remove the wheel. Use a 22-millimeter socket. Take off the lug nuts. Take the wheel off.
Now, I wanna get this wheel speed sensor wire out of the way. I'm gonna use a trim tool to remove the hold downs, this one right there and right here. And then disconnect the connector up top. I just wanna move it out of the way. Now, I'm gonna remove this bracket for the brake hose. I'm gonna use a 10-millimeter socket to take this bolt out. Oh. And sometimes they'll break. That's okay. Just set it aside.
Now, I'm gonna loosen up this nut. I'm not gonna completely take it off. I just wanna loosen it using an 18-millimeter wrench. All right. So I'll leave a couple of threads on there. That's good. Now, I'm gonna break the ball joint free from the knuckle. I'm gonna use a pickle fork. You could try tapping the knuckle, but you wanna be careful. You don't wanna break it. Just watch out for the brake hose. Make sure you're not hitting the brake hose on the other side. There we go.
Now, I'm gonna support the lower control arm with a jack stand. I wanna take the load off the upper control arm. Just lower it onto that. You could always use a floor jack. All right. Now, I'm gonna take a pry bar and just pry down on the control arm and then I can take the nut off of the ball joint. And if the stud starts spinning, just pry down on the pry bar a little bit more and then take that nut off.
You can slide the knuckle out. I could leave it right there for now. I'm gonna take these bolts out next. So that you don't break the axle, you wanna make sure that you keep the knuckle pulled in towards the vehicle so it doesn't pull out too far. So you can always use a strap like this and just tie this down so it doesn't fall out. Right now, I'm gonna use a 21-millimeter wrench on the bolt here and either a 13/16 or a 20-millimeter wrench on this side. Loosen the nut up. I might need a breaker bar. Yep.
Or you can use a 21-millimeter socket as well. Break it free. Loosen up the nut. And then take that nut off. You can take this cam off. This is like a washer that's adjustable. You can use some type of pry tool. And just slide that out. I'm gonna use an air hammer with a hammerhead and just push this bolt out. To get this bolt out, if this bracket is in your way, you can just tip up the control arm. Use a 13-millimeter socket to take this bolt out. Just slide the bracket out of your way. Just be careful not to bend the brake line. Now, just take a punch and a hammer and just tap it out the rest of the way. And you can do the same on the other side. And when you're taking that other side out, you don't have to take the shock out. You just have to rotate the cam so that it goes behind the shock.
Now, I'll just grab the upper control arm, and work it back and forth, then you can slide it up. And take the new arm. Just slide it in position and then take the bolts with the inside cam. There we go. All right. So on the outside of these cams, these have these little nylon or plastic spacers right here. That's going to make it so the alignment's close to where it should be. It's not gonna be exact. You still need to get an alignment done after you're done. So when you put these on and you put that tab through that hole, if you still have these on the vehicle, then it's gonna be close. That'll get you somewhat close to where it should be. Install the nuts. There we go.
All right. So when I go to torque these 2 bolts down, what I wanna use is my 13-millimeter, 13/16 wrench. And I want this upper control arm to be as close to ride height as possible. Ideally, you put this all back together and put the weight of the vehicle on it, and then retorque that. But that's not that easy to get to. So try to get the upper control arm as close to ride height as possible. Sometimes you take a 12-millimeter socket, just stick it under here, and that's pretty close.
And then you wanna torque this to 140 foot pounds, both this one and the other one. And once those are all torqued, you can take the socket out. Now, I can take this strap out of the way, and take the brake hose, line this back up. Put the bolt in and snug it up. Now, I'll get the ball joint lined up. You might have to use a pry bar. Get the nut started. Now, I'm gonna pry down on the control arm and then tighten that nut. Use a 19-millimeter ratchet wrench. Then if you have the ability to torque this nut, you're gonna wanna torque that to 37 foot pounds or do the best you can.
That's good. Now, I'll take this bracket for the brake hose and take a bolt. Put the bolt back in and snug it up. Take the ABS wire or the wheel speed sensor harness, and reposition this. And plug the connector back in. That's good. All right. Now you can take the grease fitting and put that in the ball joint. Get that started. And use a 7-millimeter wrench and just snug it up and give it a couple pumps. You can watch the boot of the ball joint, and then once you see it move, then it should be good enough. That's good. Now, I'm gonna raise the vehicle and reinstall the wheel. And put the lug nuts on. Now, I'm gonna torque these lug nuts to 140 foot pounds in a cross pattern to tighten the wheel down evenly. I'll just go around again and double-check.
