Specifications: 

  • Brand New Outer Tie Rod & Lower Ball Joint Kit
  • Comes as a Set of 4
    • Fits LH (Driver Side) & RH (Passenger Side) Front
  • Built to strict quality control standards
  • Direct replacements

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Direct Fit

All parts are direct fit, application-specific parts with no modifications required

Rigorously Tested

Rigorously tested and made from higher quality materials than the competition. Our parts are built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

Our parts are manufactured by some of the same factories that the OEMs use.

Prepackaged for Your Convenience

Our kits have been carefully put together to include all of the parts you need to get the job done, saving you both time and money. These kits also help take the guesswork out of finding the correct part for your vehicle’s steering or suspension system, allowing you to get started on your repair project faster.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:40)
    • Loosen the lug nut covers
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Tie Rod (1:00)
    • Measure from the boot to the outer tie rod and record it
    • Loosen the 19mm nut on the tie rod with a 19mm wrench
    • Remove the cotter pin with pliers
    • Remove the castle nut with a 17mm socket
    • Hit the knuckle with a hammer
    • Twist the tie rod out
  3. step : Installing the New Tie Rod (2:13)
    • Twist on the new tie rod
    • Push the outer tie rod down into the knuckle
    • Replace the castle nut
    • Push the cotter pin into place and bend the ends in separate directions with pliers
    • Measure and double check the distance of the boot to the tie rod
    • Turn the tie rod joint with the 14mm wrench to adjust the distance
    • Replace and tighten the 19mm nut
  4. step : Reattaching the Wheel (3:15)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to between 100 foot-pounds in a crossing or star pattern
    • Reattach the center cap

Tools needed for replacement:

    General Tools

  • Hammer
  • Jack Stands
  • Floor Jack

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Torque Wrench
  • Ratchet

  • Sockets - Metric

  • 17mm Socket
  • 19mm Socket

  • Wrenches - Metric

  • 14mm Wrench
  • 19mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1997-2000 Acura EL Front 4 Piece Set Suspension Kit
  • 1994-2001 Acura Integra Front 4 Piece Set Suspension Kit
  • 1997-2001 Honda CR-V Front 4 Piece Set Suspension Kit
  • 1992-2000 Honda Civic Front 4 Piece Set Suspension Kit
  • 1993-1997 Honda Civic Del Sol Front 4 Piece Set Suspension Kit

This part replaces:

  • OE # 53560S04013, 53560S04013
  • OE # 53540S04013, 53540S04003
  • Moog K9802
  • Moog ES3332R
  • Moog ES3331R
Part #: 1ASFK02260

Ships Same Day for orders placed by 4 P.M. ET

How-to Video:

(03:54 min)