Specifications:

  • Brand New Suspension Kit
  • Fits LH (Driver Side) & RH (Passenger Side)
  • Built to strict quality control standards
  • Direct replacements
  • Kit includes:
    • (2) Inner tie rods
    • (2) Outer tie rods
    • (2) Adjusting sleeves
    • (1) Pitman arm
    • (1) Idler arm

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Part Details

  • Kit Includes: (2) Tie Rod Adjusting Sleeves
  • Kit Includes: (1) Pitman Arm
  • Kit Includes: (2) Front Outer Tie Rods
  • Kit Includes: (1) Idler Arm
  • Kit Includes: (2) Front Inner Tie Rods
  • Quantity: 8 Piece Set

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

  1. step : Remove the wheel (1:00)
    • Loosen the lug nuts.
    • Raise and secure the vehicle
    • Remove the lug nuts and the wheel.
  2. step : Remove the front shield (1:15)
    • Use a 15 mm socket and ratchet.
    • Remove the four bolts.
  3. step : Remove the Idler Arm (1:25)
    • Remove the 24 mm bolt securing the idler arm to the steering linkage
    • Use a joint fork and a hammer to separate the joint.
    • Remove the three other bolts securing the idler arm.
    • Use a Tie Rod Puller to pull apart the idler arm and the idler shaft.
  4. step : Install the new idler arm (4:34)
    • Assemble your new idler arm to your idler shaft, threading on the bushing and nut.
    • Bolt in the idler arm assembly into place, tightening up the three nuts.
    • Bolt in the end of the idler arm assembly to the steering gear.
    • Torque the nuts and bolts to 80 ft lbs.
    • Install the cotter pin.
    • Use a grease gun and fill the grease fitting.
  5. step : Reassembly (7:25)
    • Replace the shield with the four 15mm bolts.
    • Clip the air bag harness back in.
    • Put the wheel back on and lower the car
    • Using a star pattern torque the lug nuts to 120-140 ft lbs

Tools needed for replacement:

    General Tools

  • Hammer
  • Jack Stands
  • Large C-Clamp

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Socket Extensions
  • Torque Wrench

  • Sockets - Metric

  • 15mm Socket
  • 18mm Socket
  • 19mm Socket
  • 22mm Socket
  • 24mm Socket

  • Specialty Tools

  • Grease Gun
  • Tie Rod Fork
  • Tie Rod Puller

  • Wrenches - Metric

  • 18mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 2 questions Browse 2 questions and 9 answers
Is that kit for one side or both sides?
Jets31 on Oct 24, 2017
BEST ANSWER: for sure so far so good I insalled them.then had a .alignment job truck is smooth and tight now
What brand are these parts and do they grease fittings? Are they of good quality or should I buy higher grade
James M on Apr 14, 2017
BEST ANSWER: I have been working on automobiles for fifty years with my partner in our auto body & repair facility and we have always had to use what the insurance company adjuster would pay for and often they were not OEM [ Original Equipment Manufacturer ] US manufactured parts.

Often they were a bit out tolerance wise, but plenty safe. I tell you truthfully that I am very pleased with the quality of these components that I used on my own 96' Silverado 1 ton crew cab even though they were not made in the United States.

I looked them over with the intent to send them back if I felt they were cheaply made because I could not believe how inexpensive they were. But to my amazement, they are very good castings and everything fit like GM original stuff.

The only poor quality component was the little bolts and nuts that come with the tie rod end clamping sleeves. They were too brittle and failed when tightened. But for the money, I was happy to replace them with new one's I had in the store room.

To address your question about the grease fittings, the answer is yes they did come with the components. I will always buy from this vendor for my parts needs now for two reasons. 1. because of the savings on A -1 quality stuff and 2. because I am way out on a ranch in the country, so traveling to town is costly and I can find what I need online and it is shipped very quickly right to my place.

I also bought the front wheel drive "half shafts", shock absorbers and the actuator module for the transfer case engagement yoke. Everything has been top shelf.
1ASTS00343-Shock Absorber Front
1ASTS00343-Shock Absorber Front
1AACS00008-CV Axle Shaft Pair
1AACS00008-CV Axle Shaft Pair
1AFWA00004-Four Wheel Drive Actuator
1AFWA00004-Four Wheel Drive Actuator

Vehicle Fit

  • 1999-2000 Cadillac Escalade 4 Wheel Drive 8 Piece Set Suspension Kit
  • 1993-1994 Chevy Blazer Full Size 4 Wheel Drive 8 Piece Set Suspension Kit
  • 1993-1999 Chevy K1500 Truck 8 Piece Set Suspension Kit
  • 1993-2000 Chevy K2500 Truck 8 Piece Set Suspension Kit
  • 1993-2000 Chevy K3500 Truck 8 Piece Set Suspension Kit
  • 1993-1999 Chevy Suburban K1500 8 Piece Set Suspension Kit
  • 1993-1999 Chevy Suburban K2500 8 Piece Set Suspension Kit
  • 1995-1999 Chevy Tahoe 4 Wheel Drive 8 Piece Set Suspension Kit
  • 2000 Chevy Tahoe 4 Wheel Drive 8 Piece Set Suspension Kit V8 5.7L
  • 1993-1999 GMC K1500 Truck 8 Piece Set Suspension Kit
  • 1993-2000 GMC K2500 Truck 8 Piece Set Suspension Kit
  • 1993-2000 GMC K3500 Truck 8 Piece Set Suspension Kit
  • 1993-1999 GMC Suburban K1500 8 Piece Set Suspension Kit
  • 1993-1999 GMC Suburban K2500 8 Piece Set Suspension Kit
  • 1992-1999 GMC Yukon 4 Wheel Drive 8 Piece Set Suspension Kit
  • 2000 GMC Yukon 4 Wheel Drive 8 Piece Set Suspension Kit V8 5.7L

This part replaces:

  • OE # 26048561, 7839709, 8260485610
  • OE # 26051896
  • Moog ES2838RL
  • Moog ES2004S
  • Moog K6447
  • Moog K6335
  • Moog ES2836RL
Part #: 1ASFK02238

How-to Video:

(08:13 min)