These replacement suspension parts are just what you need to ensure the safety and integrity of your vehicle's suspension and steering.

Specifications:

  • FRONT Suspension Kit includes:
    • (2) - FRONT LOWER Ball Joints - LH (Driver Side) & RH (Passenger Side)
    • (2) - FRONT INNER Tie Rod Ends - LH (Driver Side) & RH (Passenger Side)
    • (2) - FRONT OUTER Tie Rod Ends - LH (Driver Side) & RH (Passenger Side)
    • (2) - FRONT Sway Bar Links - LH (Driver Side) & RH (Passenger Side)
    • (2) - REAR Sway Bar Links - LH (Driver Side) & RH (Passenger Side)
  • Comes as shown with greasable joint & hardware
  • Direct replacement
  • Built to strict quality control standards

Worn ball joints can cause excessive front tire wear, popping or creaking in the front end, extra play in the steering system, and pose a serious safety concern. Replace loose or worn ball joints with our quality replacement. One way to diagnose a loose, or warn ball joint, is to jack the car up, so the wheel is off of the ground, then have someone try to move the wheel in and out. While they are moving the wheel check the ball joint for play, if it is moving you probably need to replace it.

Remember whenever you are replacing any front end or steering components you should have your vehicle professionally aligned as soon as possible. This will ensure proper tracking and even tire wear.

Our steering and suspension components are sealed for long life and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Direct Fit

All parts are direct fit, application-specific parts with no modifications required

Rigorously Tested

Rigorously tested and made from higher quality materials than the competition. Our parts are built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

Our parts are manufactured by some of the same factories that the OEMs use.

Prepackaged for Your Convenience

Our kits have been carefully put together to include all of the parts you need to get the job done, saving you both time and money. These kits also help take the guesswork out of finding the correct part for your vehicle’s steering or suspension system, allowing you to get started on your repair project faster.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Remove the wheel (1:14)
    • Loosen the lug nuts with your lug wrench.
    • Raise and secure the car.
    • Remove the lug nuts and remove the wheel.
  2. step : Remove the stabilizer link (1:35)
    • Spray the bolts with penetrating oil
    • Use a 5mm Allen wrench and an 18 mm wrench to remove the nut and bolt on the stabilizer link.
    • Repeat on the bottom.
    • Use a Sawzall to remove the stabilizer link if it is rusted on there.
    • You can rent a Sawzall at a home improvement supply store.
  3. step : install the new stabilizer links (6:20)
    • Put the stabilizer link in place and use your wrench to bolt the locking lug nuts on.
  4. step : Put the wheel back on (7:38)
    • Hand-tighten the lug nuts and then lower the car.
    • Refer to the owner’s manual to torque the lug nuts to the correct ft lbs.
    • Use a star pattern.

Tools needed for replacement:

    Allen Wrenches

  • 5/16 Inch Allen Wrench

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Lug Wrench

  • Wrenches - SAE

  • 3/4 Inch Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2000 Chrysler Grand Voyager Suspension Kit 10 Piece Set
  • 1996-2000 Chrysler Town & Country Suspension Kit 10 Piece Set
  • 2000 Chrysler Voyager Suspension Kit 10 Piece Set
  • 1996-2000 Dodge Caravan Suspension Kit 10 Piece Set
  • 1996-2000 Dodge Grand Caravan Suspension Kit 10 Piece Set
  • 1996-2000 Plymouth Grand Voyager Suspension Kit 10 Piece Set
  • 1996-2000 Plymouth Voyager Suspension Kit 10 Piece Set

This part replaces:

  • Moog K7301
  • Moog EV362
  • Moog K7258
  • Moog K7257
  • Moog ES3401RL
  • OE # 5272190
  • OE # 4443405
Part #: 1ASFK00447



How-to Video:

(07:55 min)