Replaces

Subaru Rear Driver or Passenger Side Wheel Bearing & Hub Assembly Timken HA590313 - TKSHR00195

Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

TIMKEN WHEEL BEARING & HUB ASSEMBLY: HA590313

This replacement wheel bearing & hub assembly is just what you need to get your vehicle in good working order again.

Specifications:

  • Brand New Timken Wheel Bearing & Hub Assembly
  • Fits either LH (Driver Side) or RH (Passenger Side) REAR
  • Replaces dealer part numbers: 28473FG000, 28473FG001, 28473AJ00A
  • 4 Bolt Flange
  • Fits 5 Lug Wheel
  • New wheel studs installed
  • Direct replacement
  • Built to strict quality control standards
  • Fits models with ABS (Anti-Lock Brakes)
  • Does NOT fit STi models

Note:
These parts are authentic Timken brand products that are supplied and packaged by Timken.   In some cases, Timken will source parts from other high quality suppliers such as SKF and Koyo. These parts are subjected to the very same testing and quality standards as all Timken products.

Item Condition: New

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge.

  1. step : Removing the Wheel (0:21)
    • Loosen the 19 mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Brakes (1:16)
    • Remove the 14 mm caliper slide bolts
    • Remove the brake caliper and hang it to relieve tension from the brake hose
    • Remove the two 14 mm caliper bracket mounting bolts
    • Remove the brake caliper mounting bracket
    • Remove the brake rotor
    • If the hand brake shoes are tight against the rotor you can remove the rubber cover and loosen the shoes with the adjuster
  3. step : Removing the Hub and Bearing (5:05)
    • Remove the 32 mm axle nut
    • Remove the four 14 mm bolts at the rear of the knuckle
    • Remove the wheel hub and bearing assembly
  4. step : Some Tips For Removing a Stuck Hub Assembly (6:49)
    • Apply rust penetrant around the hub assembly where it meets the backing plate
    • Hit it with a hammer
    • Apply heat around the hub assembly with a torch
    • Replace one of the mounting bolts not bottomed out all the way, and hammer that to push the hub assembly forward
    • Pry the hub assembly away using a pry bar and hammer
    • Remove the entire backing plate and hammer the hub assembly out from behind
  5. step : Installing the Wheel Hub and Bearing Assembly (25:12)
    • Apply anti-seize to the knuckle and axle splines
    • Insert the 14 mm mounting bolts through the mounting holes
    • Seat the backing plate on the bolts if it came off
    • Insert the hub assembly onto the axle
    • Start all four of the 14 mm bolts into the hub assembly by hand
    • Tighten the 14 mm bolts in a cross pattern
    • Torque the 14 mm bolts in a cross pattern to 48 ft-lb
  6. step : Replacing the Handbrake Hardware (Optional) (28:27)
    • If you did not need to remove the handbrake hardware to remove your wheel hub, you can skip this step
    • Apply brake grease to the brake shoe contact surfaces on the backing plate
    • Connect the front facing brake shoe to the handbrake cable
    • Place the shoe retaining pin through the backing plate and through the shoe, and the locking bracket
    • Turn the pin to lock it in place with the locking bracket
    • Seat the front facing brake shoe in place
    • Mount the rear facing brake shoe onto its retaining pin and lock it in place in the same fashion
    • Seat the rear facing brake shoe in place
    • Insert the top brake shoe bridge plate by first inserting its spring into the front facing brake shoe
    • Connect a shoe spring from the rear facing pad to the top ear
    • Connect a shoe spring from the front facing pad to the top ear
    • Insert the adjuster between the two shoes at the bottom
    • Connect the two shoes at the bottom with the long spring
  7. step : Replacing the Brakes (39:23)
    • Replace the brake rotor onto the wheel studs
    • Adjust the brake shoes with the adjuster if the rotor does not fit
    • Replace the brake caliper bracket with two 14 mm bolts
    • Torque the brake caliper bracket bolts to 49 ft-lb
    • Replace the brake caliper
    • Replace the two 14 mm caliper slider bolts
    • Hold the caliper slider with pliers if it spins
    • Torque the 14 mm caliper slider bolts to 20 ft-lb
    • Pump the brakes to compress the caliper into position
    • Replace the 32 mm axle nut
    • Torque the 32 mm axle nut to 77 ft-lbs
    • Peen over the thin edge of the axle nut into the groove in the axle
  8. step : Replacing the Wheel (48:06)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the 19 mm lug nuts preliminarily
    • Lower the vehicle partially to the ground
    • Tighten the lug nuts to 85 ft-lb in a star pattern
    • Lower the vehicle completely

Tools needed for replacement:

    General Tools

  • Hammer
  • Jack Stands
  • Rubber Mallet
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Side Cutters
  • Needle nose pliers

  • Ratchets & Related

  • Socket Extensions
  • Torque Wrench
  • Ratchet
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • 14mm Socket
  • 19mm Socket
  • 32mm Socket
  • 10mm Socket

  • Specialty Tools

  • Blowtorch

  • Wrenches - Metric

  • 14mm Wrench

5.00/ 5.0
1review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
0
0
0
0
Great price
Quality product at a great price. Exactly as described and delivered right on time.
November 24, 2018
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
2013-2016Subaru BRZ Subaru BRZ Rear Driver or Passenger Side Wheel Bearing & Hub Assembly
2009-2013Subaru Forester Subaru Forester Rear Driver or Passenger Side Wheel Bearing & Hub Assembly
2008-2011Subaru Impreza Subaru Impreza (excluding STi Models) Rear Driver or Passenger Side Wheel Bearing & Hub Assembly
2008-2014Subaru Impreza Subaru Impreza (excluding STi Models) WRX Rear Driver or Passenger Side Wheel Bearing & Hub Assembly
2010-2014Subaru Legacy Subaru Legacy Rear Driver or Passenger Side Wheel Bearing & Hub Assembly
2010-2014Subaru Outback Subaru Outback Rear Driver or Passenger Side Wheel Bearing & Hub Assembly
Part #: TKSHR00195

Out of Stock

Timken
Brand #: HA590313