In the past, replacing struts required specialized tools to compress, remove and transfer the old spring and mount.  Pre-assembled with all new parts, our complete strut and spring assemblies make this job much quicker and easier for the do-it-yourself mechanic.

Each complete strut & spring assembly contains:

  • Upper Strut Mount
  • Strut Bearing
  • Coil Spring
  • Boot & Bumper Kit
  • Gas-charged Strut 

To ensure the vehicle performs safely and as designed, we recommend replacing shocks & struts in pairs. If the damping rates are significantly different from side to side (like using different brand parts or mixing old with new) the vehicle body and wheel movement variations could cause handling irregularities. We also recommend performing an alignment after replacement. This will ensure proper tracking and protect your vehicle's tires from premature wear.

Pre-Assembled

Loaded strut & spring assemblies allow for a quicker, safer install than bare struts.  No spring compressor required! 

Trouble-Free Install

Includes the matched parts needed. New components over reused parts provide a better ride and save you from having to repair again.

Item Condition: New

WARNING:  This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Detaching the Strut (0:43)
    • Open the trunk
    • Pull back the trunk insulation
    • Pull off the strut cover
    • Remove the two 15mm nuts from the top of the strut
    • Raise and secure the vehicle
    • Apply penetrating oil to the lower strut bolt and nut
    • Remove the 18mm nut from the strut
    • Tap the strut bolt through with a hammer and pick
    • Remove the two plastic clips from the top of the strut
  2. step : Removing the Wheel (2:10)
    • Lower the vehicle to the ground
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  3. step : Removing the Strut (2:30)
    • Pry off the strut with a pry bar
    • Pull the strut down and out over the wheel
  4. step : Installing the New Strut (2:44)
    • Put the new strut into place over the wheel
    • Pull down the wheel as you push the strut into place
    • Position the strut with a pry bar
    • Hammer the bolt into the strut
    • Fasten the 18mm nut onto the strut bolt
    • Tighten the nut to between 75 - 80 foot-pounds
    • Insert the plastic clips into the top of the strut
  5. step : Reattaching the Wheel (4:01)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
  6. step : Reattaching the Strut (4:09)
    • Fasten the two 15mm nuts onto the top of the strut
    • Tighten the 15mm nuts to between 40 - 45 foot-pounds
    • Replace the strut cover
    • Put the trunk insulation back into place
  7. step : Fastening the Wheel (4:37)
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Hammer
  • Jack Stands
  • Pick

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Pry Bar

  • Sockets - Metric

  • 15mm Socket
  • 19mm Socket

  • Wrenches - Metric

  • 18mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
1999-2000Chrysler Cirrus Chrysler Cirrus Front Strut & Spring Assembly Driver Side
2001-2006Chrysler Sebring Chrysler Sebring Convertible Front Strut & Spring Assembly Driver Side
2001-2006Chrysler Sebring Chrysler Sebring Sedan Front Strut & Spring Assembly Driver Side
1999-2000Dodge Stratus Dodge Stratus Front Strut & Spring Assembly Driver Side
2001-2006Dodge Stratus Dodge Stratus Sedan Front Strut & Spring Assembly Driver Side
1999-2000Plymouth Breeze Plymouth Breeze Front Strut & Spring Assembly Driver Side

This part replaces:

  • Hollander 527-01468L
  • Hollander 527-01470L
  • Hollander 527-02028L
Part #: 1ASTS01016


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(05:01 min)