In the past, replacing struts required specialized tools to compress, remove and transfer the old spring and mount.  Pre-assembled with all new parts, our complete strut and spring assemblies make this job much quicker and easier for the do-it-yourself mechanic.

Each complete strut & spring assembly contains:

  • Upper Strut Mount
  • Strut Bearing
  • Coil Spring
  • Boot & Bumper Kit
  • Gas-charged Strut 
Pre-Assembled

Loaded strut & spring assemblies allow for a quicker, safer install than bare struts.  No spring compressor required! 

Trouble-Free Install

Includes the matched parts needed. New components over reused parts provide a better ride and save you from having to repair again.

Matched Parts

Not all shocks and struts are manufactured the same.  Mixing and matching can result in ride quality issues and decrease the life of the parts.

Saves Time & Money

Over buying the parts individually, or having to search different parts that are correct for your vehicle (because we did it for you!)

Part Details

  • Quantity: 4 Piece Set

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Remove the wheel (0:45)
    • Loosen the lug nuts
    • Raise and secure the vehicle
    • Remove the lug nuts and wheel.
  2. step : Remove the bottom of the shock (1:02)
    • Unbolt the two bottom bolts securing the shock.
    • Use a breaker bar and a 21 mm socket and some penetrating oil.
    • You might need a hammer to work the bolts out once you have removed the nuts.
    • Use a pry bar to pry the spindle free from the strut
  3. step : Remove the top of the strut (1:40)
    • Pop the hood and secure it.
    • Use your 13 mm socket and ratchet and some penetrating oil to remove the three bolts securing the top of the strut.
    • Pull the strut down and out.
  4. step : Install the new strut (2:10)
    • Work the strut into place and bolt in the top three 13 mm bolts
    • Torque the three 13 mm nuts to 35-45 ft lbs
    • Bolt in the bottom two nuts and bolts and torque to 100 ft lbs.
  5. step : Replace the wheel (3:46)
    • Put the wheel back on and hand tighten the lug nuts
    • Lower the vehicle and torque the lug nuts to 100 ft lbs

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Jack Stands

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • 13mm Socket
  • 19mm Socket
  • 21mm Socket

5.0 / 5.0
2 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
2
0
0
0
0
My 2003 Chevy Impala is riding like a new car. Thanks 1aauto!!!!
March 8, 2018
Purchased
10 months ago
These struts!
Went in like a charm, and the car rides like a new car.
August 19, 2017
Purchased
1 year ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 9 questions Browse 9 questions and 15 answers
I want to know if this lowers the vehicle at all and by how much?
Merritt L on Dec 27, 2015
BEST ANSWER: These shocks arnt lowering springs by no means. They actually might raise your car up. Depending on how old your factory struts are.
What is so different with these the Police/Taxi models?
Stephen J on Dec 12, 2015
BEST ANSWER: Normally its the ride control. The Police and Taxi models are stiffer with a different spring rate.
Will these work for my 03 Chevy impala? It's not a police car or taxi.
Kristina E on Feb 10, 2016
BEST ANSWER: Yes, these shocks will work perfectly fine. They will be a bit stiffer then your factory shock but it will bolt right up and work perfectly fine!
Will this fit my 2007 LS?
Matt C on Jun 15, 2017
BEST ANSWER: These will fit the following vehicles:

2000-2011 Chevy Impala Front & Rear Strut & Spring Assembly 4 Piece Set for Police & Taxi Models excluding 18 Inch Wheels

1998-2002 Olds Intrigue Front & Rear Strut & Spring Assembly 4 Piece Set

You only need to verify the fit information listed.
Will these fit my 2008 chevy impala ss with 18 inch factor rims?
Trey M on Mar 22, 2016
BEST ANSWER: Yes... It raised my car by a half inch no problems with the install only took me about 45 minutes a side
The Title says it will fit a 2012 Impala, but in the Q&A section, it says these will not fit a 2012 Impala. Which is correct?
Jerome M on Jun 26, 2018
BEST ANSWER: Hello,
These struts are listed for fit the '12MY as long as it is not the police or taxi model. We may have updated our listings since that question was answered. Thank you!
Will it fit the 12 impala lt?
MMNes on Oct 5, 2017
BEST ANSWER: No, these are meant for 2006 - 2011 models.
Will this set fit a 2011 impala Ltz with 18" rims?
Art D on Mar 26, 2017
BEST ANSWER: No, these will not fit your 2011 Impala LTZ with 18" wheels.
Will I be able to fit 22 inch rims on my 08 impala ltz with this if not how do I ?
sam12 s on May 26, 2016
BEST ANSWER: These will fit OEM size wheels. Any further mods will need assistance outside of 1A Auto.

Vehicle Fit

Year Make Model Description
2000-2012Chevy Impala Chevy Impala Front & Rear Strut & Spring Assembly 4 Piece Set for Police & Taxi Models (excluding 18 Inch Wheels) TRQ SCA57015
1998-2002Oldsmobile Intrigue Olds Intrigue Front & Rear Strut & Spring Assembly 4 Piece Set TRQ SCA57015

This part replaces:

  • Monroe 171670
  • Monroe 171671L
  • Monroe 171671R
  • TRQ SCA57015
Part #: 1ASSP00327


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

TRQ
Brand #: SCA57015

How-to Video:

(04:55 min)