Replaces
Strut & Spring Assembly Pair TRQ SCA57356 - 1ASSP01469
1ASSP01469
In the past, replacing struts required specialized tools to compress, remove and transfer the old spring and mount. Pre-assembled with all new parts, our complete strut and spring assemblies make this job much quicker and easier for the do-it-yourself mechanic.
Each complete strut & spring assembly contains:
- Upper Strut Mount
- Strut Bearing
- Coil Spring
- Boot & Bumper Kit
- Gas-charged Strut
Loaded strut & spring assemblies allow for a quicker, safer install than bare struts. No spring compressor required!
Trouble-Free InstallIncludes the matched parts needed. New components over reused parts provide a better ride and save you from having to repair again.
Matched PartsNot all shocks and struts are manufactured the same. Mixing and matching can result in ride quality issues and decrease the life of the parts.
Saves Time & MoneyOver buying the parts individually, or having to search different parts that are correct for your vehicle (because we did it for you!)
Part Details
- Quantity: Pair
Lifetime Warranty
This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.
-
step : Removing the Wheel (0:38)
- Loosen the lug nut covers with a 19mm socket
- Pry off the center cap with a flat blade screwdriver
- Loosen the lug nuts with the vehicle on the ground
- Raise the vehicle with a floor jack
- Secure the vehicle on jack stands
- Remove the lug nuts
- Pull off the wheel
-
step : Removing the Sway Bar Link (1:03)
- Place a 14mm wrench to hold the back
- Remove the nut with an 18mm socket
- Remove the sway bar link
-
step : Installing the New Sway Bar Link (1:41)
- Push the sway bar link into place
- Replace and tighten the 18mm nuts
-
step : Reattaching the Wheel (2:03)
- Slide the wheel into place
- Start the lug nuts by hand
- Tighten the lug nuts preliminarily
- Lower the vehicle to the ground
- Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
- Reattach the center cap
- Tighten the lug nut covers with a 19mm socket
Tools needed for replacement:
- Floor Jack
- Jack Stands
- Torque Wrench
- Ratchet
- 18mm Socket
- 19mm Socket
- 14mm Wrench
General Tools
Ratchets & Related
Sockets - Metric
Wrenches - Metric
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
Vehicle Fit
- 2005-2009 Buick Allure Rear Strut & Spring Assembly Pair for Models with 17 Inch Wheels TRQ SCA57356
- 2005-2009 Buick LaCrosse Rear Strut & Spring Assembly Pair for Models with 17 Inch Wheels TRQ SCA57356
- 2004-2014 Chevy Impala Rear Strut & Spring Assembly Pair for Models with 17 Inch Wheels TRQ SCA57356
- 2014 Chevy Impala Limited Rear Strut & Spring Assembly Pair for Models with 17 Inch Wheels TRQ SCA57356
- 2004-2007 Chevy Monte Carlo Rear Strut & Spring Assembly Pair for Models with 17 Inch Wheels TRQ SCA57356
- 2004-2008 Pontiac Grand Prix Rear Strut & Spring Assembly Pair for Models with 17 Inch Wheels TRQ SCA57356
This part replaces:
- KYB SR4089
- TRQ SCA57356
