Specifications:

  • Brand New Bellow Kit
  • Comes as a Pair
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacements
  • Built to strict quality control standards

Part Details

  • Quantity: Pair

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

    After completing this repair, it's recommended to have your car aligned

  1. step : Removing the Wheel (0:52)
    • Loosen the lug nuts with the vehicle on the ground
    • Remove the hubcap
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Outer Tie Rod (1:12)
    • Measure from the end of the tie rod boot to the end of the tie rod
    • Spray the 22mm nut on the outer tie rod with penetrating oil
    • Hold the inner tire rod with a 13mm wrench
    • Loosen the nut on the outer tie rod with a 22mm wrench
    • Remove the cotter pin from the ball joint nut with pliers
    • Remove the 17mm nut from the ball joint
    • Hit the spindle with a hammer to knock the ball joint free
    • Spin the outer tie rod free
  3. step : Installing the New Outer Tie Rod (3:00)
    • Screw the grease fitting on the bottom of the new tie rod
    • Tighten it with a 7mm socket
    • Twist the outer tie rod into the inner tie rod
    • Measure from the outside of the boot to the inside of the tie rod to match your previous measurement
    • Hold the outer tie rod with a wrench while tightening the 22mm nut to the tie rod
    • Attach a grease gun to the ball joint fitting and give it several pumps
  4. step : Reattaching the Wheel (4:42)
    • Slide the wheel into place
    • Replace the hub cap
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to between 100 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    General Tools

  • Hammer
  • Jack Stands
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Bearing Grease
  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Adjustable Wrench
  • Needle nose pliers

  • Ratchets & Related

  • Torque Wrench
  • A Piece of Pipe (for leverage)
  • Ratchet

  • Sockets - Metric

  • 22mm Socket
  • 7mm Socket
  • 17mm Socket

  • Specialty Tools

  • Grease Gun

  • Wrenches - Metric

  • 13mm Wrench
  • 22mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1978-1980 Ford Fiesta Steering Rack & Pinion Bellow Pair
  • 1973 Ford Mustang Steering Rack & Pinion Bellow Pair for Models with Manual Steering
  • 1979-1983 Ford Mustang Steering Rack & Pinion Bellow Pair for Models with Manual Steering
  • 1974-1978 Ford Mustang II Steering Rack & Pinion Bellow Pair for Models with Manual Steering
  • 1986-1993 Ford Tempo Steering Rack & Pinion Bellow Pair for Models with Manual Steering
  • 1995-2006 Hyundai Accent Steering Rack & Pinion Bellow Pair
  • 1992-2000 Hyundai Elantra Steering Rack & Pinion Bellow Pair
  • 1986-1993 Hyundai Excel Steering Rack & Pinion Bellow Pair for Models with Manual Steering
  • 1994 Hyundai Excel Steering Rack & Pinion Bellow Pair
  • 1991-1994 Hyundai Scoupe Steering Rack & Pinion Bellow Pair for Models with Manual Steering
  • 1995 Hyundai Scoupe Steering Rack & Pinion Bellow Pair
  • 1989-1992 Hyundai Sonata Steering Rack & Pinion Bellow Pair for Models with Mando Steering Rack
  • 1995-1998 Hyundai Sonata Steering Rack & Pinion Bellow Pair
  • 1997-2001 Hyundai Tiburon Steering Rack & Pinion Bellow Pair
  • 1979-1984 Mercury Capri Steering Rack & Pinion Bellow Pair for Models with Manual Steering
  • 1984-1985 Mercury Topaz Steering Rack & Pinion Bellow Pair for Models with Manual Steering Externally Threaded Steering Racks
  • 1979-1983 Mercury Zephyr Steering Rack & Pinion Bellow Pair for Models with Manual Steering
  • 1990-1994 Mitsubishi Precis Steering Rack & Pinion Bellow Pair for Models with Manual Steering
  • 1993-1996 Nissan Altima Steering Rack & Pinion Bellow Pair
  • 1990-1993 Volvo 240 Steering Rack & Pinion Bellow Pair
  • 1989 Volvo 244 Steering Rack & Pinion Bellow Pair
  • 1989 Volvo 245 Steering Rack & Pinion Bellow Pair
  • 1985-1992 Volvo 740 Steering Rack & Pinion Bellow Pair for Models with Cam Steering Rack
  • 1985 Volvo 745 Steering Rack & Pinion Bellow Pair for Models with Cam Steering Rack
  • 1988-1990 Volvo 760 Steering Rack & Pinion Bellow Pair for Models with Cam Steering Rack
  • 1994-1995 Volvo 940 Steering Rack & Pinion Bellow Pair
  • 1994-1997 Volvo 960 Steering Rack & Pinion Bellow Pair
  • 1997-1998 Volvo S90 Steering Rack & Pinion Bellow Pair
  • 1998 Volvo V90 Steering Rack & Pinion Bellow Pair

This part replaces:

  • Moog K9882
Part #: 1ASFK04292

How-to Video:

(05:41 min)