Specifications:

  • Brand New Steering Rack & Tie Rod Kit
  • New Power Rack & Pinion Assembly
    • not remanufactured, no core charge
  • Rack includes gear assembly, inner tie rods, & rack boots
  • Direct replacements
  • Built to strict quality control standards

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Direct Fit

All parts are direct fit, application-specific parts with no modifications required

Rigorously Tested

Rigorously tested and made from higher quality materials than the competition. Our parts are built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

Our parts are manufactured by some of the same factories that the OEMs use.

Prepackaged for Your Convenience

Our kits have been carefully put together to include all of the parts you need to get the job done, saving you both time and money. These kits also help take the guesswork out of finding the correct part for your vehicle’s steering or suspension system, allowing you to get started on your repair project faster.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:43)
    • Pry off the hub cap with a flat blade screwdriver
    • Loosen the 35mm hub nut with the vehicle on the ground
    • Loosen the lug nuts
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Outer Tie Rod (1:08)
    • Spray both ends of the outer tie rod with penetrating oil
    • Measure from the either end of the outer tie rod
    • Place a 26mm wrench on the larger nut
    • Place a 22mm wrench on the smaller nut
    • Break the 22mm nut free
    • Straighten the cotter pin with pliers and pull it through
    • Remove the nut with a 21mm socket from the wheel knuckle
    • Hit the wheel knuckle with a hammer
    • Twist off the outer tie rod
    • Remove the 22mm nut off the outer tie rod
  3. step : Installing the New Outer Tie Rod (3:08)
    • Mark where the 22mm nut was located on the old tie rod to the new tie rod
    • Screw on the nut
    • Twist the outer tie rod into place
    • Push the outer tie rod into the wheel knuckle
    • Measure and check the outer tie rod distance
    • Tighten the 21mm nut on the wheel knuckle
    • Insert and twist the cotter pin with a pair of pliers
    • Tighten the two nuts on the outer tie rod
  4. step : Reattaching the Wheel (4:33)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the hub nut
    • Torque the lug nuts to 100 ft/lbs in a crossing or star pattern
    • Torque the hub nut to 103 ft/lbs
    • Reattach the center cap

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Measuring Tape
  • Hammer
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 19mm Socket
  • 21mm Socket

  • Wrenches - Metric

  • 26mm Wrench
  • 22mm Wrench
  • 10mm Wrench

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
1
0
0
0
0
made steering work
I had a shop put this on and everything went great made the car drive better and works great
April 5, 2017
Purchased
1 year ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2004-2007 Buick Rainier Steering Kit 3 Piece Set
  • 2003-2006 Chevy SSR Steering Kit 3 Piece Set
  • 2002 Chevy Trailblazer Steering Kit for Models with 16mm Thread Tie Rods 3 Piece Set
  • 2003-2009 Chevy Trailblazer Steering Kit 3 Piece Set
  • 2002 Chevy Trailblazer EXT LT Steering Kit for Models with 16mm Thread Tie Rods 3 Piece Set
  • 2002 GMC Envoy Steering Kit for Models with 16mm Thread Tie Rods 3 Piece Set
  • 2003-2009 GMC Envoy Steering Kit 3 Piece Set
  • 2003-2006 Isuzu Ascender Steering Kit 3 Piece Set
  • 2007 Isuzu Ascender Steering Kit for Models with RPO Code N40 (Non-Variable Effort Steering) for Models without Sport Suspension 3 Piece Set
  • 2008 Isuzu Ascender Steering Kit 3 Piece Set
  • 2002 Olds Bravada Steering Kit for Models with 16mm Thread Tie Rods 3 Piece Set
  • 2003-2004 Olds Bravada Steering Kit 3 Piece Set
  • 2005-2009 Saab 9-7X Steering Kit 3 Piece Set

This part replaces:

  • A1 Cardone 97-1014
  • Moog ES3675
  • Moog ES3676
  • Hollander 551-00128, 551-02073
  • OE # 26100286
  • OE # 26100287
  • OE # 19207782, 19207780, 15162147
Only 4 left in stock
Part #: 1ASFK03626


How-to Video:

(05:20 min)