Specifications:

  • Brand New Steering Kit
  • Comes as a 6 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacements
  • Built to strict quality control standards

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Direct Fit

All parts are direct fit, application-specific parts with no modifications required

Rigorously Tested

Rigorously tested and made from higher quality materials than the competition. Our parts are built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

Our parts are manufactured by some of the same factories that the OEMs use.

Prepackaged for Your Convenience

Our kits have been carefully put together to include all of the parts you need to get the job done, saving you both time and money. These kits also help take the guesswork out of finding the correct part for your vehicle’s steering or suspension system, allowing you to get started on your repair project faster.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:45)
    • Remove the lug nut covers with a 19mm socket
    • Pull off the hub cap
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Outer Tie Rod (1:18)
    • Twist the cotter pin out of the tie rod nut with needle nose pliers
    • Remove the 18mm nut from the tie rod
    • Measure from the boot of the inner tie rod to the center of the outer tie rod
    • Note this measurement
    • Loosen the 7/8 inch nut that holds the inner to the outer tie rod
    • Thread the 18mm nut onto the tie rod slightly
    • Strike the tie rod with a hammer to loosen it from the spindle
    • Twist off the outer tie rod
  3. step : Installing the New Outer Tie Rod (2:32)
    • Attach the grease fitting to the new outer tie rod
    • Tighten the grease fitting with a 7mm socket and ratchet
    • Twist the outer tie rod onto the inner tie rod
    • Push the tie rod into the spindle
    • Thread the 18mm nut onto the tie rod
    • Measure the distance from the boot to the center of the tie rod
    • This measurement should match the one taken in Step 2
    • Adjust the tie rod as necessary
    • Tighten the 18mm nut
    • Put the cotter pin through the 18mm nut and fold it over with needle nose pliers
    • Hold the nut that connects the inner to the outer tie rod with a 7/8 inch wrench
    • Turn the inner tie rod with a 13mm wrench
    • Add grease to the grease fitting with a grease gun
  4. step : Reattaching the Wheel (3:58)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
    • Put on the hub cap, lining up the hole with the valve stem
    • Tighten the lug nut covers with a 19mm socket

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Jack Stands
  • Measuring Tape

  • Materials, Fluids, and Supplies

  • Bearing Grease

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet

  • Sockets - Metric

  • 18mm Socket
  • 19mm Socket
  • 7mm Socket

  • Wrenches - Metric

  • 13mm Wrench
  • 22mm Wrench

  • Wrenches - SAE

  • 7/8 Inch Wrench

4.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
0
1
0
0
0
Good value. Fast shipping.
My only complain is that the picture is deceptive. It shows hose clamps for the bellows but you send zip ties instead.
June 22, 2017
Purchased
12 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 1 answer
Does this fit a 2009 Chevy impala police car ?
Big joe on Dec 20, 2017
BEST ANSWER: This will fit a 2009 Chevy Impala which does not have the RPO code FE4. With police or taxi models, the suspension in most cases is more heavy duty and requires special parts. Please check your vehicle for the appropriate RPO codes.

Vehicle Fit

  • 1997-2005 Buick Century 6 Piece Set Steering Kit
  • 2005-2009 Buick LaCrosse 6 Piece Set Steering Kit
  • 1997-2004 Buick Regal 6 Piece Set Steering Kit
  • 2000-2003 Chevy Impala 6 Piece Set Steering Kit
  • 2004-2011 Chevy Impala 6 Piece Set Steering Kit without RPO Code FE4 (Special Ride & Handling Suspension)
  • 2000-2007 Chevy Monte Carlo 6 Piece Set Steering Kit
  • 1998-2002 Olds Intrigue 6 Piece Set Steering Kit
  • 2004-2008 Pontiac Grand Prix 6 Piece Set Steering Kit

This part replaces:

  • Moog EV195
  • Moog ES3459
  • OE # 26021769
  • Moog K6298
  • OE # 26056811
  • OE # 26086580
Part #: 1ASFK02865

Ships Same Day for orders placed by 4 P.M. ET

How-to Video:

(04:49 min)