This replacement front steering kit is just what you need to bring back the safety and integrity of your vehicle's suspension and steering.

Specifications:

  • FRONT Steering Kit Includes:
    • (2) - FRONT UPPER Ball Joints - LH (Driver Side) & RH (Passenger Side)
      • Replaces dealer part numbers: 15575901, 15617715, 15634385, 15634904, 15659518, 15687080
    • (2) - FRONT LOWER Ball Joints (45.79 mm Diameter Press-In Type) - LH (Driver Side) & RH (Passenger Side)
      • Replaces dealer part numbers: 12380415, 12383410
    • (2) - FRONT INNER Tie Rods - LH (Driver Side) & RH (Passenger Side)
      • Replaces dealer part number: 26059036
    • (2) - FRONT OUTER Tie Rods - LH (Driver Side) & RH (Passenger Side)
      • Replaces dealer part numbers: 26000150, 26059031, 26059033
    • (1) - FRONT Pitman Arm
      • Replaces dealer part number: 26051896
    • (1) - FRONT Idler Arm
      • Replaces dealer part numbers: 26028523, 26028525, 26059030
  • Direct fit replacements
  • Built to strict quality control standards
  • Fits 4WD (Four Wheel Drive) Models only
  • Fits models with Stamped Steel Control Arms only
    • Does NOT fit models with Forged Control Arms

Remember whenever you are replacing any front end or steering components you should have your vehicle professionally aligned as soon as possible. This will ensure proper tracking and even tire wear.

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Direct Fit

All parts are direct fit, application-specific parts with no modifications required

Rigorously Tested

Rigorously tested and made from higher quality materials than the competition. Our parts are built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

Our parts are manufactured by some of the same factories that the OEMs use.

Prepackaged for Your Convenience

Our kits have been carefully put together to include all of the parts you need to get the job done, saving you both time and money. These kits also help take the guesswork out of finding the correct part for your vehicle’s steering or suspension system, allowing you to get started on your repair project faster.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Remove the wheel (1:00)
    • Loosen the lug nuts.
    • Raise and secure the vehicle
    • Remove the lug nuts and the wheel.
  2. step : Remove the front shield (1:15)
    • Use a 15 mm socket and ratchet.
    • Remove the four bolts.
  3. step : Remove the Idler Arm (1:25)
    • Remove the 24 mm bolt securing the idler arm to the steering linkage
    • Use a joint fork and a hammer to separate the joint.
    • Remove the three other bolts securing the idler arm.
    • Use a Tie Rod Puller to pull apart the idler arm and the idler shaft.
  4. step : Install the new idler arm (4:34)
    • Assemble your new idler arm to your idler shaft, threading on the bushing and nut.
    • Bolt in the idler arm assembly into place, tightening up the three nuts.
    • Bolt in the end of the idler arm assembly to the steering gear.
    • Torque the nuts and bolts to 80 ft lbs.
    • Install the cotter pin.
    • Use a grease gun and fill the grease fitting.
  5. step : Reassembly (7:25)
    • Replace the shield with the four 15mm bolts.
    • Clip the air bag harness back in.
    • Put the wheel back on and lower the car
    • Using a star pattern torque the lug nuts to 120-140 ft lbs

Tools needed for replacement:

    General Tools

  • Hammer
  • Jack Stands
  • Large C-Clamp

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Socket Extensions
  • Torque Wrench

  • Sockets - Metric

  • 15mm Socket
  • 18mm Socket
  • 19mm Socket
  • 22mm Socket
  • 24mm Socket

  • Specialty Tools

  • Grease Gun
  • Tie Rod Fork
  • Tie Rod Puller

  • Wrenches - Metric

  • 18mm Wrench

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
1
0
0
0
0
Great product
Shipped fast. Showed up in great condition. Works perfectly. Website even had a video of how to install it, Very helpful.
February 6, 2018
Purchased
over 3 years ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 2 answers
How do I know if I have stamped steel control arms instead of forged?
Cross on Oct 30, 2017
BEST ANSWER: Look for seems, besides weld seems. If there's no seems, then it's stamped.Enter

Vehicle Fit

  • 1999-2000 Cadillac Escalade 4 Wheel Drive with Stamped Steel Lower Control Arms Steering Kit 10 Piece Set
  • 1995-1999 Chevy K1500 Truck with Stamped Steel Lower Control Arms Steering Kit 10 Piece Set
  • 1995-2000 Chevy K2500 Truck 6 Lug Wheels with Stamped Steel Lower Control Arms Steering Kit 10 Piece Set
  • 1995-1999 Chevy Suburban K1500 with Stamped Steel Lower Control Arms Steering Kit 10 Piece Set
  • 1995-2000 Chevy Tahoe V8 5.7L 4 Wheel Drive with Stamped Steel Lower Control Arms Steering Kit 10 Piece Set
  • 1995-1999 GMC K1500 Truck with Stamped Steel Lower Control Arms Steering Kit 10 Piece Set
  • 1995-2000 GMC K2500 Truck 6 Lug Wheels with Stamped Steel Lower Control Arms Steering Kit 10 Piece Set
  • 1995-1999 GMC Suburban K1500 with Stamped Steel Lower Control Arms Steering Kit 10 Piece Set
  • 1995-2000 GMC Yukon V8 5.7L 4 Wheel Drive with Stamped Steel Lower Control Arms Steering Kit 10 Piece Set

This part replaces:

  • Moog K6477
  • Moog ES2838RL
  • Moog K6292
  • Moog K6447
  • Moog K6335
  • Moog ES2836RL
  • OE # 26051896
Part #: 1ASFK00708


How-to Video:

(08:13 min)