Specifications:

  • Comes as a 6 Piece Kit:
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacement
  • Built to strict quality control standards

Our steering and suspension components are sealed for long life and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Direct Fit

All parts are direct fit, application-specific parts with no modifications required

Rigorously Tested

Rigorously tested and made from higher quality materials than the competition. Our parts are built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

Our parts are manufactured by some of the same factories that the OEMs use.

Prepackaged for Your Convenience

Our kits have been carefully put together to include all of the parts you need to get the job done, saving you both time and money. These kits also help take the guesswork out of finding the correct part for your vehicle’s steering or suspension system, allowing you to get started on your repair project faster.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Remove the wheel and tire (1:30)
    • Raise and secure the vehicle.
    • Remove the lug nuts and then the wheel.
  2. step : Remove Caliper (2:00)
    • Turn wheels all the way in the opposite direction of the side you are working on.
    • Use your 15mm socket wrench to remove the caliper bolts.
    • Use a wire tie to help prevent stress on the caliper.
  3. step : Remove brake disk (2:44)
    • Take care not to touch the disk, and if you do make sure to clean it with rubbing alcohol or mineral spirits.
  4. step : Remove Hub (2:56)
    • Remove the 3 bolts securing the hub using your 13mm socket and 3/8 extension and ratchet or breaker bar.
    • You can use penetrating oil to help.
    • Use a 35mm socket to remove the hub nut.
    • Give the axle a slight tap with a hammer to loosen it.
    • Use a rubber mallet to break it free, and work around the flange with the hammer to pull it off.
    • Leave the top 13mm loosely still in to prevent the hub from flying out if you hit it too hard.
    • Remove the hub, using driving tools to help work it out of the steering knuckle.
    • Clean up any corrosion with a wire brush.
  5. step : Install new hub (8:30)
    • Use some penetrating oil to prep the knuckle for the new hub.
    • Watch part 2 to install your new 1A Auto hub!

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Hammer
  • Jack Stands
  • Rubber Mallet

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Socket Extensions
  • Torque Wrench

  • Screwdrivers & Related

  • Phillips Head Screwdriver

  • Sockets - Metric

  • 13mm Socket
  • 19mm Socket
  • 32mm Socket
  • 35mm Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1997-2001 Buick Century with ABS Brakes 6 Piece Set Steering Kit
  • 1997-2001 Buick Regal with ABS Brakes 6 Piece Set Steering Kit
  • 2000-2001 Chevy Impala with ABS Brakes 6 Piece Set Steering Kit
  • 2000-2001 Chevy Monte Carlo with ABS Brakes 6 Piece Set Steering Kit
  • 1998-2001 Olds Intrigue with ABS Brakes 6 Piece Set Steering Kit

This part replaces:

  • Moog EV195
  • Moog ES3459
  • Dorman 951-016
  • Hollander 538-01680B
  • OE # 12429204, 7470017
  • OE # 26021769
  • Reference Number 513121
Part #: 1AHTF00017


How-to Video:

(09:37 min)