Replaces

Steering Column Shift Tube Clamp Ford OEM F2DZ-7E400-A - FDSTC00023

Specifications:

  • Brand New Ford Steering Column Shift Tube Clamp
  • Fits Upper or Lower steering column bushing
  • Original equipment part
  • Built to strict quality control standards

Wear and Tear

This item is backed by a 60-day warranty against defects in materials and workmanship under its intended use. The warranty does not cover normal wear and tear. Please keep your invoice for proof of this warranty.

  1. step : Disconnecting the Battery (1:19)
    • Remove the negative battery terminal with an 8mm socket and ratchet
  2. step : Removing the Steering Column Cover (1:42)
    • Remove the Phillips head screws from the lower steering column cover
    • Tilt the column down
    • Work off the top half of the cover
    • Unscrew the tilt column level
    • Remove the lower half of the cover
  3. step : Removing the Knee Panel and Plate (2:23)
    • Remove the four 7mm bolts on the bottom of the knee panel
    • Pull the knee panel off
    • Remove the five 8mm screws from the metal plate
  4. step : Removing the Gear Selector (3:16)
    • Remove the two 13mm nuts securing the U-brace at the bottom of the column
    • Hold the column up
    • Remove the two 13mm nut at the base of the steering column
    • Carefully lower the column
    • Press the tab and remove the boot from the gear selector
    • Remove the spring collar from the bottom of the gear selector pin
    • Gently tap the pin out of the gear selector with a hammer
    • Pry the clip and gear selector off with a flat blade screwdriver
  5. step : Removing the Shift Selector Tube (5:06)
    • Remove the seven T30 Torx screws that secure the shift tube
    • Remove the red wire loop from the gear selector
    • Lift up the gear selector tube
    • Remove the two T30 Torx screws at the back of the selector tube
    • Remove the shift selector tube
  6. step : Disassembling the Shift Selector Tube (6:09)
    • Remove the spring
    • Tap the lock pin out with a hammer
    • Pull the pin out with pliers
    • Remove the interlock arm
    • Remove the plunger
  7. step : Reassembling the Shift Selector Tube (7:18)
    • Coat the plunger with grease
    • Install the plunger into the shift tube
    • Insert the spring over the short end of the tube
    • Reinstall the interlock
    • Press the pin into the interlock
    • Hammer the pin in with a hammer
  8. step : Installing the Shift Selector Tube (8:08)
    • Insert the shifter tube into the plate
    • Tighten the two T30 screws at the end
    • Press the shift tube into the column
    • Reinstall the clamps, with the interlock arm on top of the bracket's lever
    • Tighten the seven T30 Torx screws
  9. step : Reinstalling the Gear Selector (9:25)
    • Start the clip on to the gear selector
    • Set the gear selector into place
    • Reinstall the pin and tap the splines in
    • Insert the spring collar onto the pin
    • Slide the boot onto the gear selector
    • Reattach the overdrive wire into its retainer
    • Snap the boot into its holders
    • Reattach the red wire loop to the gear selector
    • Lift the column onto its studs
    • Start the bolts in the back
    • Insert the U-brace into place
    • Tighten the 13mm nuts to the column
    • Tighten the 13mm nuts to the U-brace
  10. step : Checking the Shift Indicator Needle's Alignment (11:37)
    • Check the alignment of the shift indicator needle
    • Use the adjustor wheel forward to move the indicator to the left (Park)
    • Or use the adjustor wheel backwards to move the indicator to the right (Drive)
    • Test the selector for proper alignment
  11. step : Reinstalling the Steering Column Cover (13:00)
    • Insert the upper steering column cover into place
    • Insert the lower steering column cover so it snaps with the upper cover
    • Tighten the Phillips head screws to the column cover
    • Twist the tilt column lever into place
  12. step : Reinstalling the Knee Panel (13:36)
    • Insert the metal plate into place
    • Tighten the five 8mm screws to the plate
    • Press the knee panel into place
    • Reinstall the hood release
    • Tighten the four 7mm bolts to the bottom of the panel
  13. step : Reconnecting the Battery (14:28)
    • Reconnect the negative battery terminal
    • Tighten the terminal with an 8mm socket and ratchet
There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1992-1997 Ford Aerostar Upper or Lower Steering Column Shift Tube Clamp Ford OEM F2DZ-7E400-A
  • 1992-1996 Ford Bronco Upper or Lower Steering Column Shift Tube Clamp Ford OEM F2DZ-7E400-A
  • 1992-2004 Ford E150 Van Upper or Lower Steering Column Shift Tube Clamp Ford OEM F2DZ-7E400-A
  • 1992-2004 Ford E250 Van Upper or Lower Steering Column Shift Tube Clamp Ford OEM F2DZ-7E400-A
  • 1992-2004 Ford E350 Van Upper or Lower Steering Column Shift Tube Clamp Ford OEM F2DZ-7E400-A
  • 1996-2004 Ford E450 Van Upper or Lower Steering Column Shift Tube Clamp Ford OEM F2DZ-7E400-A
  • 2002-2003 Ford E550 Van Upper or Lower Steering Column Shift Tube Clamp Ford OEM F2DZ-7E400-A
  • 2000-2005 Ford Excursion Upper or Lower Steering Column Shift Tube Clamp Ford OEM F2DZ-7E400-A
  • 1997-2002 Ford Expedition Upper or Lower Steering Column Shift Tube Clamp Ford OEM F2DZ-7E400-A
  • 1995-2003 Ford Explorer Upper or Lower Steering Column Shift Tube Clamp Ford OEM F2DZ-7E400-A
  • 2002-2005 Ford Explorer Sport Trac Upper or Lower Steering Column Shift Tube Clamp Ford OEM F2DZ-7E400-A
  • 2004 Ford F150 Heritage Truck Upper or Lower Steering Column Shift Tube Clamp Ford OEM F2DZ-7E400-A
  • 1992-2003 Ford F150 Truck Upper or Lower Steering Column Shift Tube Clamp Ford OEM F2DZ-7E400-A
  • 1997-1999 Ford F250 Light Duty Truck Upper or Lower Steering Column Shift Tube Clamp Ford OEM F2DZ-7E400-A
  • 1999-2007 Ford F250 Super Duty Truck Upper or Lower Steering Column Shift Tube Clamp Ford OEM F2DZ-7E400-A
  • 1992-1997 Ford F250 Truck Upper or Lower Steering Column Shift Tube Clamp Ford OEM F2DZ-7E400-A
  • 1999-2007 Ford F350 Super Duty Truck Upper or Lower Steering Column Shift Tube Clamp Ford OEM F2DZ-7E400-A
  • 1992-1997 Ford F350 Truck Upper or Lower Steering Column Shift Tube Clamp Ford OEM F2DZ-7E400-A
  • 1999-2007 Ford F450 Truck Upper or Lower Steering Column Shift Tube Clamp Ford OEM F2DZ-7E400-A
  • 1999-2007 Ford F550 Truck Upper or Lower Steering Column Shift Tube Clamp Ford OEM F2DZ-7E400-A
  • 2000-2003 Ford F650 Truck Upper or Lower Steering Column Shift Tube Clamp Ford OEM F2DZ-7E400-A
  • 2000-2003 Ford F750 Truck Upper or Lower Steering Column Shift Tube Clamp Ford OEM F2DZ-7E400-A
  • 1998-2011 Ford Ranger Upper or Lower Steering Column Shift Tube Clamp Ford OEM F2DZ-7E400-A
  • 1990-2003 Ford Taurus Upper or Lower Steering Column Shift Tube Clamp Ford OEM F2DZ-7E400-A
  • 1995-2003 Ford Windstar Upper or Lower Steering Column Shift Tube Clamp Ford OEM F2DZ-7E400-A
  • 2002 Lincoln Blackwood Upper or Lower Steering Column Shift Tube Clamp Ford OEM F2DZ-7E400-A
  • 1990-2002 Lincoln Continental Upper or Lower Steering Column Shift Tube Clamp Ford OEM F2DZ-7E400-A
  • 1998-2002 Lincoln Navigator Upper or Lower Steering Column Shift Tube Clamp Ford OEM F2DZ-7E400-A
  • 1990-2003 Lincoln Town Car Upper or Lower Steering Column Shift Tube Clamp Ford OEM F2DZ-7E400-A
  • 1997-2001 Mercury Mountaineer Upper or Lower Steering Column Shift Tube Clamp Ford OEM F2DZ-7E400-A
  • 1990-2005 Mercury Sable Upper or Lower Steering Column Shift Tube Clamp Ford OEM F2DZ-7E400-A
  • 1993-1995 Mercury Villager Upper or Lower Steering Column Shift Tube Clamp Ford OEM F2DZ-7E400-A

This part replaces:

  • Ford OEM F2DZ-7E400-A
  • OE # F2DZ7E400A, GC2Z7E400A
Only 4 left in stock
Part #: FDSTC00023

Ships Same Day for orders placed by 4 P.M. ET

Brand #: F2DZ-7E400-A

How-to Video:

(14:58 min)