Kit Includes: (2) Front Sway Bar Links (2) Front Lower Control Arms with Ball Joints (2) Front Outer Tie Rods (2) Front Upper Control Arms with Ball Joints (2) Front Steering Rack & Pinion Bellows (2) Front Inner Tie Rods
Install Tip: When replacing steering components, have a professional alignment performed afterwards. This ensures proper tracking and even tire wear.
Complete Repair in One Purchase - Stop searching for parts individually and complete your repair with a customized kit or set from DIY Solutions.
High-Quality Parts from Trusted Brands - DIY Solutions' kits and sets are selected from the best automotive brands and include hard-to-find and even obsolete parts you may need for your vehicle.
Guaranteed Fit - DIY Solutions ensures its selected parts are quality-tested to guarantee fit and function.
Item Condition:New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
How To Replace Outer Tie Rod 2004-08 Ford F150
How to Replace Front Upper Control Arm with Ball Joint 2004-2015 Nissan Titan
How to Replace Front Sway Bar Links 2004-2005 Nissan Titan
How to Replace Front Inner Tie Rod End 2004-2015 Nissan Titan
How to Replace Front Left Lower Control Arm 2004-2015 Nissan Titan
How to Replace Front Outer Tie Rod End 2004-2015 Nissan Titan
How to Replace Steering Rack Pinion Bellow 2004-2015 Nissan Titan
Created on:
Tools used
Adjustable Wrench
Torque Wrench
Hammer
Jack Stands
Grease Gun
21mm Socket
Measuring Tape
Bearing Grease
21mm wrench
7mm Socket
10mm Socket
Ratchet
Floor Jack
1. Removing the Wheel
Pry off the center cap with a flat blade screwdriver
Loosen the lug nuts with the vehicle on the ground
Raise the vehicle with a floor jack
Secure the vehicle on jack stands
Remove the lug nuts
Pull off the wheel
2. Removing the Outer Tie Rod
Turn the wheel by hand
Remove the 21mm nut from the outer tie rod
Thread the 21mm nut on a couple of turns
Hold the tie rod with an adjustable wrench
Loosen the tie rod adjusting nut with an adjustable wrench
Strike the steering knuckle with a hammer
Twist the 21mm nut off the tie rod
Measure the distance from the tie rod boot to the outer tie rod stud
Note that measurement
Twist off the outer tie rod.
3. Installing the Tie Rod
Twist on the outer tie rod
Measure the distance from the tie rod boot to the outer tie rod stud
This should be the same as the distance noted in Step 2
Move the adjusting nut as necessary
Push the tie rod into the wheel knuckle
Fasten the 21mm nut onto the tie rod
Tighten the 21mm nut to 111 foot-pounds of torque
Tighten the adjusting nut
Twist the grease fitting into the tie rod
Tighten the grease fitting with a 7mm socket and ratchet
Add grease to the grease fitting with a grease gun
4. Reattaching the Wheel
Slide the wheel into place
Start the lug nuts by hand
Tighten the lug nuts preliminarily
Lower the vehicle to the ground
Tighten the lug nuts to 120 foot-pounds in a crossing or star pattern
Reattach the center cap
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace an outer tie rod on this 2005 Ford F150. We show you on the driver side but the passenger side is the same procedure. The items you'll need for this is a new outer tie rod from 1AAuto.com; a 7, 10, and 21mm socket and ratchet with a piece of pipe for leverage; two adjustable wrenches; a tape measure; a hammer; a torque wrench; and jack and jack stands.
Start off by prying off the hub cap. Then loosen up these lug nuts using a 21mm socket and ratchet and a piece of pipe for some extra leverage. Once you get each of them loosened up you can raise the vehicle and remove them the rest of the way. Now pull the wheel off.
Now turn the wheel and then remove this 21mm nut at the top of your outer tie rod. Then once you remove it, you want to just put it back on just a couple threads. Spray the nut at the end of your outer tie rod with some penetrating fluid, and then, using two adjustable wrenches, just loosen it up. Now hammer the knuckle until the outer tie rod drops down. Now you can remove that nut and just set your outer tie rod off to the side.
Now measure from the boot on your inner tie rod to the center of your outer tie rod, and just remember that distance. Then you can twist your outer tie rod free. We'll fast forward as Mike does that.
On the left is the old outer tie rod. On the right, is the new one from 1A Auto. You can see they're identical and they'll fit exactly the same. Take your new outer tie rod and twist it into place. We'll fast forward as Mike does that. Now, measure from the boot to the inside of the outer tie rod and make sure it's the same distance. If it is, you're all set. If not, you'll have to move that nut to adjust it.
Now, feed your outer tie rod up through the wheel knuckle and replace that nut and tighten it up. If the studs start spinning when you use your 21mm socket just use a 21mm wrench and a 10mm socket to hold the stud in place and tighten it up. Then torque that to 111 foot pounds.
Now, using two adjustable wrenches just tighten that nut back up, and then put your grease fitting into place on the outer tie rod. Then just tighten it up with a 7mm socket and ratchet. Using a grease gun, just top it off with some grease.
Now we'll fast forward as Mike replaces the wheel, and replaces the lug nuts, and tightens them preliminary, and then lowers the vehicle and tightens them the rest of the way. Then torque each of them, in a crossing pattern, to 120 foot pounds. Then just replace your hub cap and you're all set.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Torque Wrench
Hammer
17mm Wrench
19mm Socket
Liquid Thread Locker
Trim Tool Set
Pliers
Pocket Screwdriver
21mm Socket
Rubber Mallet
Phillips Bit in a Ratchet
Ratchet
Floor Jack
Tools used
21mm Socket
Torque Wrench
17mm Socket
19mm Wrench
Jack Stands
Ratchet
Floor Jack
Tools used
21mm Socket
Torque Wrench
Locking Pliers
Inner Tie Rod Removal Tool
Hammer
Jack Stands
Copper Anti-Seize
22mm Wrench
Ratchet
Floor Jack
Pliers
Tools used
Torque Wrench
Hammer
18mm Wrench
Pry Bar
Jack Stands
19mm Wrench
18mm Socket
19mm Socket
21mm Socket
Pickle Fork
Side Cutters
21mm wrench
32mm Socket
Punch
Copper Anti-Seize
Floor Jack
Wire Brush
22mm Socket
Marker / Writing Utensil
Tools used
21mm Socket
Torque Wrench
Locking Pliers
Hammer
Jack Stands
Copper Anti-Seize
22mm Wrench
Ratchet
Floor Jack
Pliers
Tools used
21mm Socket
Torque Wrench
Locking Pliers
Hammer
Jack Stands
Copper Anti-Seize
22mm Wrench
Ratchet
Floor Jack
Pliers
SUS04045
In Stock
Product Reviews
Loading reviews
4.67/ 5.09
9 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
7
1
1
0
0
Happy customer
J
October 9, 2019
Fast delivery time, quality parts, great price. What more could you want?
Suspension kit
Jose
March 24, 2020
The parts were delivered fast. They all fit no problems with installing. Now my truck drive better.
Great Kit and Great Quality
Mark
August 23, 2020
The suspension kit came packaged and labeled perfectly. All parts of this kit fit perfectly on my 2004 Nissan Titan.
Perfect fit 05 Nissan Titan
Jacob
September 18, 2020
Installed new upper & lower control arms, inner and outer tie rod ends, shocks & strut assembly, and new wheel bearings also purchased from A1 auto. Everything fit up perfect. No issues at all. Control arms didnt come with mounting hardware. If youre going to replace them Id recommend buying new ones for the lower control arms at least. Very pleased with the price and figment.
great value fast shipping car rides like new again
Gets it done.
Paul
August 21, 2022
Decent stuff, trq is ok. Aint moog, but gets it done.
Pedro
December 15, 2023
Perfect very good pieces
Successful purchase!
Ronald
January 21, 2024
The parts arrived on time and in excellent condition due to the packaging. All parts were delivered and installation was completed in a timely fashion as all parts were exact fits. Thank you.
Customer Q&A
Will this kit work after I put a 4" leveling kit on my truck? "Front & back" The leveling kit is already installed and I'm having issues with the upper control arm rubbing on my top strut mount. And also I took my truck to get an alignment they trieJune 11, 2019
William C
10
Currently, we do not carry this part for your vehicle. All of the parts we carry are designed to work on non-modified vehicles. Thanks!
June 11, 2019
Adam G
Does the infiniti 12 piece suspension kit also include all the bolts, nuts, washers etc for installation?November 1, 2019
Scott S
10
The ones that need to be replaced, but you reuse most of your bolts and washers
November 1, 2019
Jason N
10
Thank you for your inquiry. This kit will not include any additional hardware other than what is shown in the listing photos. If your existing hardware is in good condition it may be reused, otherwise, it would need to be sourced locally. Please let us know if you have any further questions.
November 1, 2019
A C
10
Yes
November 1, 2019
Junior J
10
yes
November 1, 2019
Mitchell M
10
It did not come all the nuts and bolts. It did come with castle nuts and cotter pins though.
November 1, 2019
G R
Do this fit a Nissan Titan 2005 4x4?March 13, 2020
J E
10
Thank you for your inquiry. This will be the correct fit for that vehicle. Please let us know if you have any further questions.
March 13, 2020
A C
Do I need to purchase anything else for the back?October 25, 2020
Marcelino D
10
This suspension kit will not include any parts for the rear.
October 26, 2020
Jessica D
Does this kit fit a 2012 Nissan Titan SV 4x4?March 19, 2022
David P
10
Yes, this part will fit your vehicle.
March 19, 2022
Cristina P
10
Yes it does works great. Sorry about the delay on the answer !!!
March 22, 2022
Charles W
Does this kit work on a 2008 infinity qx56 2 wheel drive?September 14, 2023
Floyd C
10
Yes, these parts are listed to fit a 2008 Infiniti QX56 2WD.
September 15, 2023
Kemal S
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.