Our steering and suspension components are sealed for long life and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Direct Fit

All parts are direct fit, application-specific parts with no modifications required

Rigorously Tested

Rigorously tested and made from higher quality materials than the competition. Our parts are built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

Our parts are manufactured by some of the same factories that the OEMs use.

Prepackaged for Your Convenience

Our kits have been carefully put together to include all of the parts you need to get the job done, saving you both time and money. These kits also help take the guesswork out of finding the correct part for your vehicle’s steering or suspension system, allowing you to get started on your repair project faster.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Inner Tie Rod (0:53)
    • Raise and secure the vehicle
    • Measure the length of the inner tie rod to the outer tie rod with a tape measure
    • Measure this length at extension and in compression
    • Note those measurements
    • Clean grease from the inner tie rod fitting
    • Loosen the inner tie rod from the steering rack with an adjustable wrench
    • Hold the outer tie rod in place with a wrench
    • Loosen the inner tie rod from the outer tie rod with the adjustable wrench
    • Remove the tie rod at the steering rack
    • Turn the inner tie rod counterclockwise to remove it from the outer tie rod
  2. step : Installing the New Inner Tie Rod (3:38)
    • Apply thread lock to the threads on the steering rack side of the inner tie rod
    • Use a floor jack to keep the stabilizer link above the working area
    • Thread the inner tie rod on to the steering rack
    • Tighten the inner tie rod to between 70 – 80 foot-pounds of torque
    • Twist the nut onto the outer end of the inner tie rod by hand
    • Turn the tire in to push the inner tie rod into the outer tie rod
  3. step : Adjusting the Inner Tie Rod (6:19)
    • Measure the length of the inner tie rod to the outer tie rod with a tape measure
    • Turn the inner tie rod with the adjustable wrench until its length is the noted length from Step 1
  4. step : Greasing the Fittings (7:33)
    • Use a grease gun to add grease to the inner tie rod fitting
    • Add grease until the tie rod boot starts to change shape
    • Add grease to other fittings as necessary

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Bearing Grease
  • Liquid Thread Locker
  • Paper Towels

  • Pliers, Cutters & misc Wrenches

  • Adjustable Wrench

  • Ratchets & Related

  • Torque Wrench

  • Specialty Tools

  • Grease Gun

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2002-2006 Cadillac Escalade 10 Piece Set Steering & Suspension Kit for Models with 4 Groove Pitman Arm
  • 2003-2006 Cadillac Escalade ESV 10 Piece Set Steering & Suspension Kit for Models with 4 Groove Pitman Arm
  • 2002-2006 Cadillac Escalade EXT 10 Piece Set Steering & Suspension Kit for Models with 4 Groove Pitman Arm
  • 2002-2006 Chevy Avalanche 1500 10 Piece Set Steering & Suspension Kit for Models with 4 Groove Pitman Arm
  • 1999-2006 Chevy Silverado 1500 4 Wheel Drive 10 Piece Set Steering & Suspension Kit for Models with 4 Groove Pitman Arm
  • 2007 Chevy Silverado 1500 Classic 4 Wheel Drive 10 Piece Set Steering & Suspension Kit for Models with 4 Groove Pitman Arm
  • 2000-2006 Chevy Suburban 1500 10 Piece Set Steering & Suspension Kit for Models with 4 Groove Pitman Arm
  • 2000 Chevy Tahoe 10 Piece Set Steering & Suspension Kit excluding Z71 Models for Models with 4 Groove Pitman Arm
  • 2001-2006 Chevy Tahoe 10 Piece Set Steering & Suspension Kit for Models with 4 Groove Pitman Arm
  • 1999-2006 GMC Sierra 1500 4 Wheel Drive 10 Piece Set Steering & Suspension Kit for Models with 4 Groove Pitman Arm
  • 2007 GMC Sierra 1500 Classic 4 Wheel Drive 10 Piece Set Steering & Suspension Kit for Models with 4 Groove Pitman Arm
  • 2000 GMC Yukon 10 Piece Set Steering & Suspension Kit excluding Denali Models for Models with 4 Groove Pitman Arm
  • 2001-2006 GMC Yukon 10 Piece Set Steering & Suspension Kit for Models with 4 Groove Pitman Arm
  • 2000-2006 GMC Yukon XL 1500 10 Piece Set Steering & Suspension Kit for Models with 4 Groove Pitman Arm

This part replaces:

  • Hollander 511-01044
  • OE # 12471379
  • OE # 12475478
  • OE # 12475485
  • OE # 15047200
  • OE # 15245582
  • OE # 15295861
  • OE # 15864153
  • OE # 15922557
  • OE # 19149615
  • OE # 19149617
  • OE # 26059210
  • Dorman 520-116
  • Moog ES3488
  • Moog ES3493T
  • Moog K6534
  • Moog K6536
  • Moog K6541
  • Moog K80942
Part #: 1ASFK05520


How-to Video:

(08:32 min)