Our steering and suspension components are sealed for long life and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Direct Fit

All parts are direct fit, application-specific parts with no modifications required

Rigorously Tested

Rigorously tested and made from higher quality materials than the competition. Our parts are built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

Our parts are manufactured by some of the same factories that the OEMs use.

Prepackaged for Your Convenience

Our kits have been carefully put together to include all of the parts you need to get the job done, saving you both time and money. These kits also help take the guesswork out of finding the correct part for your vehicle’s steering or suspension system, allowing you to get started on your repair project faster.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (1:03)
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Outer Tie Rod (1:24)
    • Turn the brake rotor by hand or turn the steering wheel to turn the rotor
    • Measure the distance from the end of the boot to the center of the tie rod end
    • Note that measurement
    • Loosen the tie rod lock nut with a 15/16" wrench
    • Loosen the 21mm nut from the tie rod
    • Strike the steering knuckle with a hammer to loosen it
    • Lift the tie rod end out of the steering knuckle
    • Twist off the outer tie rod by hand
  3. step : Installing the Outer Tie Rod (2:18)
    • Twist on the outer tie rod
    • Push the tie rod into the steering knuckle
    • Thread the 22mm castle nut onto the tie rod by hand
    • Measure the distance from the end of the boot to the center of the tie rod end
    • This should be the same as the measurement from Step 2
    • Twist the grease fitting into the tie rod
    • Tighten the castle nut to 50-55 foot-pounds of torque
    • Put the cotter pin into the castle nut
    • Twist on the cotter pin with pliers
    • Hold the inner tie rod with a 16mm wrench
    • Tighten the locking nut with a 15/16" wrench
    • Add grease to the tie rod with a grease gun
  4. step : Reattaching the Wheel (4:24)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100-110 foot-pounds in a crossing or star pattern
    • Reattach the center cap

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Floor Jack
  • Hammer

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Torque Wrench
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 7mm Socket
  • 21mm Socket
  • 22mm Socket

  • Specialty Tools

  • Grease Gun

  • Wrenches - Metric

  • 16mm Wrench

  • Wrenches - SAE

  • 15/16 Inch Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2007-2014 Cadillac Escalade 4 Piece Set Steering & Suspension Kit for Models with Stamped Steel Lower Control Arms
  • 2007-2014 Cadillac Escalade ESV 4 Piece Set Steering & Suspension Kit for Models with Stamped Steel Lower Control Arms
  • 2007-2013 Cadillac Escalade EXT 4 Piece Set Steering & Suspension Kit for Models with Stamped Steel Lower Control Arms
  • 2007-2010 Chevy Avalanche 1500 4 Piece Set Steering & Suspension Kit for Models with Stamped Steel Lower Control Arms
  • 2007 Chevy Silverado 1500 New Body Style 4 Piece Set Steering & Suspension Kit for Models with Stamped Steel Lower Control Arms
  • 2008-2013 Chevy Silverado 1500 4 Piece Set Steering & Suspension Kit for Models with Stamped Steel Lower Control Arms
  • 2007-2013 Chevy Suburban 1500 4 Piece Set Steering & Suspension Kit for Models with Stamped Steel Lower Control Arms
  • 2007-2014 Chevy Tahoe 4 Piece Set Steering & Suspension Kit for Models with Stamped Steel Lower Control Arms
  • 2007 GMC Sierra 1500 New Body Style 4 Piece Set Steering & Suspension Kit for Models with Stamped Steel Lower Control Arms
  • 2008-2013 GMC Sierra 1500 4 Piece Set Steering & Suspension Kit for Models with Stamped Steel Lower Control Arms
  • 2007-2014 GMC Yukon 4 Piece Set Steering & Suspension Kit for Models with Stamped Steel Lower Control Arms
  • 2007-2013 GMC Yukon XL 1500 4 Piece Set Steering & Suspension Kit for Models with Stamped Steel Lower Control Arms

This part replaces:

  • Moog K6541
  • Moog ES800223
  • OE # 12475478
  • OE # 15254061
Part #: 1ASFK05473


How-to Video:

(05:10 min)