Our steering and suspension components are sealed for long life and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Direct Fit

All parts are direct fit, application-specific parts with no modifications required

Rigorously Tested

Rigorously tested and made from higher quality materials than the competition. Our parts are built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

Our parts are manufactured by some of the same factories that the OEMs use.

Prepackaged for Your Convenience

Our kits have been carefully put together to include all of the parts you need to get the job done, saving you both time and money. These kits also help take the guesswork out of finding the correct part for your vehicle’s steering or suspension system, allowing you to get started on your repair project faster.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Remove the wheel (1:30)
    • Loosen the lug nuts.
    • Raise and secure the vehicle.
    • Remove the wheel.
  2. step : Remove the tie rod assembly (2:00)
    • Remove the tie rod bolt.
    • Use a pickle fork and hammer to separate it.
    • Use an adjustable wrench and a fitted wrench to remove the tie rod assembly.
  3. step : Install the new tie rod assembly (4:00)
    • Adjust your new tie rod assembly to match the old one for a preliminary alignment.
    • Mount the new tie rod assembly and tighten it in with a wrench.
    • Tighten the nut on the tie rod stud to 65 ft lbs.
    • Install the cotter pin.
    • Use a 7 mm wrench to install the grease fitting
    • With a grease gun, grease the inner and outer joints.
  4. step : Put the wheel back on (7:00)
    • Preliminarily tighten the lug nuts.
    • Lower the car and torque the lug nuts to 120 ft lbs using a star pattern.

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Jack Stands
  • Rubber Mallet

  • Pliers, Cutters & misc Wrenches

  • Adjustable Wrench
  • Lug Wrench
  • Needle nose pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench

  • Sockets - Metric

  • 35mm Socket
  • 7mm Socket

  • Specialty Tools

  • Grease Gun
  • Tie Rod Fork
  • Tie Rod Puller

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 1 answer
Are these parts greeseable?
Brandon S on Mar 3, 2018
BEST ANSWER: Hello,
These ball joints are lubricated and sealed at the factory. Thank you!

Vehicle Fit

  • 2002-2006 Chevy Avalanche 2500 with 3 Groove Pitman Arm Steering & Suspension Kit 10 Piece Set
  • 2001-2003 Chevy Silverado 1500 HD with 3 Groove Pitman Arm Steering & Suspension Kit 10 Piece Set
  • 2005-2006 Chevy Silverado 1500 HD with 3 Groove Pitman Arm Steering & Suspension Kit 10 Piece Set
  • 2007 Chevy Silverado 1500 HD Classic with 3 Groove Pitman Arm Steering & Suspension Kit 10 Piece Set
  • 1999-2004 Chevy Silverado 2500 with 3 Groove Pitman Arm Steering & Suspension Kit 10 Piece Set
  • 2001-2010 Chevy Silverado 2500 HD with 3 Groove Pitman Arm Steering & Suspension Kit 10 Piece Set
  • 2007 Chevy Silverado 2500 HD Classic with 3 Groove Pitman Arm Steering & Suspension Kit 10 Piece Set
  • 2001-2010 Chevy Silverado 3500 with 3 Groove Pitman Arm Steering & Suspension Kit 10 Piece Set
  • 2007 Chevy Silverado 3500 Classic with 3 Groove Pitman Arm Steering & Suspension Kit 10 Piece Set
  • 2001-2010 Chevy Suburban 2500 with 3 Groove Pitman Arm Steering & Suspension Kit 10 Piece Set
  • 2001-2003 GMC Sierra 1500 HD with 3 Groove Pitman Arm Steering & Suspension Kit 10 Piece Set
  • 2005-2006 GMC Sierra 1500 HD with 3 Groove Pitman Arm Steering & Suspension Kit 10 Piece Set
  • 2007 GMC Sierra 1500 HD Classic with 3 Groove Pitman Arm Steering & Suspension Kit 10 Piece Set
  • 1999-2004 GMC Sierra 2500 with 3 Groove Pitman Arm Steering & Suspension Kit 10 Piece Set
  • 2001-2010 GMC Sierra 2500 HD with 3 Groove Pitman Arm Steering & Suspension Kit 10 Piece Set
  • 2007 GMC Sierra 2500 HD Classic with 3 Groove Pitman Arm Steering & Suspension Kit 10 Piece Set
  • 2001-2010 GMC Sierra 3500 with 3 Groove Pitman Arm Steering & Suspension Kit 10 Piece Set
  • 2007 GMC Sierra 3500 Classic with 3 Groove Pitman Arm Steering & Suspension Kit 10 Piece Set
  • 2001-2010 GMC Yukon XL 2500 with 3 Groove Pitman Arm Steering & Suspension Kit 10 Piece Set
  • 2003-2009 Hummer H2 with 3 Groove Pitman Arm Steering & Suspension Kit 10 Piece Set

This part replaces:

  • Hollander 511-01044
  • Hollander 511-01045
  • OE # 12479051
  • OE # 15224737
  • OE # 15295861
  • OE # 15864153
  • OE # 15891515
  • OE # 15891516
  • OE # 26059210
  • Dorman 520-150
  • Moog ES3488
  • Moog ES3609
  • Moog K620053
  • Moog K6535
  • Moog K6654
  • Moog K6693
Part #: 1ASFK05372



How-to Video:

(07:45 min)