Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Part Details

  • Kit Includes: (2) Front Sway Bar Links
  • Kit Includes: (2) Front Strut & Spring Assemblies
  • Kit Includes: (2) Front Outer Tie Rods
  • Quantity: 10 Piece Set
  • Kit Includes: (2) Steering Rack & Pinion Bellows
  • Kit Includes: (2) Front Inner Tie Rods

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

  1. step : Removing the Wheel (0:35)
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Outer Tie Rod (0:59)
    • Turn the wheels by hand for better access to the tie rod
    • Remove the cotter pin from the outer tie rod with pliers
    • Remove the castle nut from the tie rod with an adjustable wrench
    • Measure the distance from the inner tie rod to the end of the outer tie rod
    • Note that measurement
    • Loosen the nut that connects the outer to the inner tie rod
    • Strike the wheel knuckle with a hammer to loosen the outer tie rod
    • Lift the outer tie rod out of the wheel knuckle
    • Twist off the outer tie rod
  3. step : Removing the Inner Tie Rod (1:59)
    • Twist off the nut that connects the outer to the inner tie rod
    • Pull the small boot clamp off the inner tie rod with pliers
    • Pry off the large boot clamp with a hammer and a flat blade screwdriver
    • Pull off the boot
    • Remove the inner tie rod with a pipe wrench
  4. step : Installing the New Inner Tie Rod (2:46)
    • Twist the new inner tie rod into place
    • Put a wire tie on the large end of the boot
    • Put the boot into place
    • Tighten the wire tie
    • Push on the small boot clamp with pliers
    • Twist on the nut that connects the outer to the inner tie rod
  5. step : Reinstalling the Outer Tie Rod (3:43)
    • Twist your outer tie rod onto the inner tie rod
    • Measure the distance from the inner tie rod to the end of the outer tie rod
    • This should be the same measurement as noted in Step 2
    • Thread the nut that connects the outer to the inner tie rod
    • Push the outer tie rod into the steering knuckle
    • Fasten the castle nut onto the outer tie rod
    • Line up the castle nut with the cotter pin hole
    • Push the cotter pin into place
    • Twist the cotter pin into place with pliers
    • Tighten the nut that connects the outer to the inner tie rod
    • Fill the outer tie rod bearing with bearing grease, using a grease gun
  6. step : Reattaching the Wheel (4:56)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds of torque in a crossing or star pattern

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Hammer
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Bearing Grease
  • Wire Ties

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers
  • Pipe Wrench
  • Adjustable Wrench

  • Ratchets & Related

  • Torque Wrench

  • Specialty Tools

  • Grease Gun

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
2001-2005Chrysler Sebring Chrysler Sebring Coupe 10 Piece Set Steering & Suspension Kit
2001-2005Dodge Stratus Dodge Stratus Coupe 10 Piece Set Steering & Suspension Kit
2000-2005Mitsubishi Eclipse Mitsubishi Eclipse 10 Piece Set Steering & Suspension Kit

This part replaces:

  • Moog ES2347RL
  • Moog K7430
  • Moog K7431
  • Moog EV457
  • Beck Arnley 103-2880
  • Hollander 527-59858L, 527-59856L
  • Hollander 527-59857R, 527-59855R
  • OE # MR333763
  • OE # MR297333
  • OE # MR519046
  • OE # 4553530010
Part #: 1ASFK05229


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(05:28 min)