Specifications:

  • Brand New Steering & Suspension Kit
  • Comes as a 12 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacements
  • Built to strict quality control standards

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

An adjustable ball joint will look slightly different than a standard, non-adjustable version.  The stud will be offset once installed and can be rotated in order to allow a greater range of vehicle suspension alignment.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Direct Fit

All parts are direct fit, application-specific parts with no modifications required

Rigorously Tested

Rigorously tested and made from higher quality materials than the competition. Our parts are built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

Our parts are manufactured by some of the same factories that the OEMs use.

Prepackaged for Your Convenience

Our kits have been carefully put together to include all of the parts you need to get the job done, saving you both time and money. These kits also help take the guesswork out of finding the correct part for your vehicle’s steering or suspension system, allowing you to get started on your repair project faster.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:53)
    • Loosen the lug nuts
    • Raise and support the vehicle
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Upper Control Arm (1:21)
    • Remove the 19mm nut from the upper control arm ball joint
    • Support the wheel spindle with a bungee cord
    • Tap the wheel spindle with a hammer to loosen the ball joint stud
    • Separate the ball joint from the wheel spindle
    • Open the hood
    • If you are working on the driver side, release the power steering reservoir tab
    • Move the power steering reservoir aside
    • Remove the two 10mm bolts from the coolant reservoir
    • Move the coolant reservoir aside
    • Open the brake fluid reservoir door
    • Remove the two 18mm control arm bolts from the strut tower
    • Pull out the two captured bolts that hold the control arm to the wheel well
    • Pull the control arm down and out
  3. step : Installing the Control Arm and Wheel (6:23)
    • Lift the control arm into place
    • Insert the two bolt that hold the control arm to the wheel well
    • Insert the ball joint stud into the wheel spindle
    • Start the 19mm nut onto the ball joint stud
    • Tighten the 19mm nut to 35 foot-pounds of torque
    • Turn the 19mm nut 90 degrees farther
    • Remove the bungee cord from the wheel spindle
    • Slide on the wheel
    • Start the lug nuts
    • Lower the vehicle to put weight on the suspension
    • Fasten the 18mm nuts onto the control arm bolts at the strut tower
    • Torque the 18mm nuts to 55 foot-pounds
    • Close the brake reservoir access door, If you worked on the driver's side
    • Put the coolant reservoir into place
    • Insert the two 10mm bolts for the coolant reservoir
    • Clip the power steering reservoir onto the coolant reservoir
    • Close the hood
    • Tighten the lug nuts to 110 foot-pounds in a crossing pattern

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Hammer
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Gloves
  • Bungee Cord

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Sockets - Metric

  • 21mm Socket
  • 18mm Socket
  • 19mm Socket

  • Wrenches - Metric

  • 18mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2005-2010 Chrysler 300 Rear Wheel Drive 12 Piece Set Steering & Suspension Kit
  • 2008-2010 Dodge Challenger 12 Piece Set Steering & Suspension Kit
  • 2006 Dodge Charger 12 Piece Set Steering & Suspension Kit
  • 2007-2010 Dodge Charger Rear Wheel Drive 12 Piece Set Steering & Suspension Kit
  • 2005-2008 Dodge Magnum Rear Wheel Drive 12 Piece Set Steering & Suspension Kit

This part replaces:

  • Hollander 512-00449
  • Hollander 512-01474L
  • Hollander 512-01473R
  • Hollander 511-01108L
  • Hollander 511-01107R
  • OE # 68002123AC
  • OE # 5180606AA, 5180607AB, 4782613AC
  • OE # 5180606AA, 5180606AB, 4782612AC
  • OE # 52013468AC, 52106710AC
  • OE # 4782740AB, 4782741AB
  • OE # 68028831AB
  • OE # 4782665AB
  • OE # 4782666AB
  • Dorman 521-121
  • Dorman 521-122
  • Dorman 521-014
  • Dorman 521-007
  • Dorman 521-008
  • Reference Number MS25120
  • Reference Number MS25121
  • Moog K620258
  • Moog K620257
  • Moog K640664
  • Moog K620177
  • Moog K620178
  • Moog ES3571
  • Moog EV80702
  • Moog K7469
Part #: 1ASFK05190


How-to Video:

(09:43 min)