Specifications:

  • Brand New Steering & Suspension Kit
  • Comes as a 10 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacements
  • Built to strict quality control standards

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Part Details

  • Kit Includes: (2) Front Lower Ball Joints
  • Kit Includes: (2) Front Outer Tie Rods
  • Kit Includes: (2) Front Sway Bar Links
  • Quantity: 10 Piece Set
  • Kit Includes: (2) Front Strut & Spring Assemblies
  • Kit Includes: (2) Front Inner Tie Rods

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

  1. step : Remove the wheel (0:45)
    • Loosen the lug nuts
    • Raise and secure the vehicle
    • Remove the lug nuts and wheel.
  2. step : Remove the bottom of the shock (1:02)
    • Unbolt the two bottom bolts securing the shock.
    • Use a breaker bar and a 21 mm socket and some penetrating oil.
    • You might need a hammer to work the bolts out once you have removed the nuts.
    • Use a pry bar to pry the spindle free from the strut
  3. step : Remove the top of the strut (1:40)
    • Pop the hood and secure it.
    • Use your 13 mm socket and ratchet and some penetrating oil to remove the three bolts securing the top of the strut.
    • Pull the strut down and out.
  4. step : Install the new strut (2:10)
    • Work the strut into place and bolt in the top three 13 mm bolts
    • Torque the three 13 mm nuts to 35-45 ft lbs
    • Bolt in the bottom two nuts and bolts and torque to 100 ft lbs.
  5. step : Replace the wheel (3:46)
    • Put the wheel back on and hand tighten the lug nuts
    • Lower the vehicle and torque the lug nuts to 100 ft lbs

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Jack Stands

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • 13mm Socket
  • 19mm Socket
  • 21mm Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question
Will this fit a 2006 impala ss?
Ryan R on Apr 30, 2018

Vehicle Fit

  • 1997-2005 Buick Century 10 Piece Set Steering & Suspension Kit
  • 2005-2007 Buick LaCrosse 10 Piece Set Steering & Suspension Kit
  • 2008-2009 Buick LaCrosse V6 3.6L 10 Piece Set Steering & Suspension Kit
  • 2008-2009 Buick LaCrosse V6 3.8L 10 Piece Set Steering & Suspension Kit
  • 1997-2004 Buick Regal 10 Piece Set Steering & Suspension Kit
  • 2000-2003 Chevy Impala (excluding Police Package) 10 Piece Set Steering & Suspension Kit
  • 2004-2011 Chevy Impala without RPO Code FE4 (Special Ride & Handling Suspension) (excluding Police Package) 10 Piece Set Steering & Suspension Kit
  • 2000-2007 Chevy Monte Carlo 10 Piece Set Steering & Suspension Kit

This part replaces:

  • Moog K5342
  • Moog EV195
  • Moog K5331
  • Moog ES3459
  • Hollander 527-01315A/B
  • OE # 26021769
  • OE # 15851956
  • OE # 88965333, 22157089, 88955451
  • Monroe 181661
  • Monroe 171661
  • KYB SR4002
Part #: 1ASFK05150

How-to Video:

(04:55 min)