Specifications:

  • Brand New Steering & Suspension Kit
  • Comes as a Set of 12
    • Fits LH (Driver Side) & RH (Passenger side)
  • Direct replacements
  • Built to strict quality control standards

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Part Details

  • Kit Includes: (2) Front Outer Tie Rods
  • Quantity: 12 Piece Set
  • Kit Includes: (2) Front Lower Control Arms with Ball Joints
  • Kit Includes: (2) Front Sway Bar Links
  • Kit Includes: (2) Front Wheel Bearings
  • Kit Includes: (2) Front Strut & Spring Assemblies
  • Kit Includes: (2) Front Inner Tie Rods

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

  1. step : Remove the wheel (1:10)
    • Loosen the lug nuts
    • Raise and secure the vehicle
    • Remove the lug nuts and the wheel.
  2. step : Remove the brakes (1:35)
    • Turn the wheel to better access the caliper
    • Use a flat blade screwdriver to compress the caliper piston
    • Remove the two 10 mm bolts to remove the caliper.
    • Fasten the caliper up with wire ties out of the way
    • Remove the rotor, hammering it off if its rusted onto the hub.
  3. step : Remove the hub (3:10)
    • Remove the hub nut with a 34 mm socket and impact wrench.
    • If you don’t have an impact wrench, put the wheel and lug nuts back on and lower the car and use a breaker bar.
    • Unbolt the three 18 mm hub bolts.
    • Take caution not to damage the CV boot.
    • Break the hub loose with a hammer and remove it.
  4. step : Install the new hub (5:55)
    • Place the hub onto the steering knuckle and work the axle into place.
    • Bolt the three 18 mm bolts into place.
    • Torque them to 90 ft lbs, rotating so they get torqued evenly.
    • Replace the hub nut, but do not tighten all the way.
  5. step : Reassemble the brakes (8:45)
    • Put the rotor on and put a lug nut on just to keep it from running away on you while you put the caliper back on
    • Put the pads into the caliper and compress the piston with a c-clamp
    • Bolt the 10 mm caliper bolts back in
    • Put the wheel back on and hand tighten the lug nuts
    • Torque the hub nut to 105 ft lbs
    • Torque the lug nuts to 90-100 ft lbs using a star pattern.
    • Pump the brakes a few times to recompress the caliper pistons and do a few 5-10 mph stops in the driveway before road testing.

Tools needed for replacement:

    General Tools

  • Large C-Clamp
  • Large Hammer

  • Ratchets & Related

  • Ratchet
  • Socket Extensions
  • Torque Wrench

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • 10mm Socket
  • 18mm Socket
  • 19mm Socket
  • 34mm Socket

  • Wrenches - Metric

  • 10mm Wrench
  • 18mm Wrench
  • 19mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1999-2004 Chrysler 300M 12 Piece Set Steering & Suspension Kit
  • 1998-2004 Chrysler Concorde 12 Piece Set Steering & Suspension Kit
  • 1999-2001 Chrysler LHS 12 Piece Set Steering & Suspension Kit
  • 1998-2004 Dodge Intrepid 12 Piece Set Steering & Suspension Kit

This part replaces:

  • Moog K7211
  • Moog K7213
  • Moog K7342
  • Dorman 520-303
  • Dorman 520-304
  • Dorman 951-034
  • Hollander 512-01083R
  • Hollander 512-01083L
  • Hollander 538-01289
  • OE # 5003930AA
  • OE # 5017461AA
  • OE # 5017460AA
  • OE # 4616402
  • OE # 4616403
  • OE # 4782254AB, 4782232AA
  • OE # 4593450AA
  • Monroe 181667
  • Monroe 181668
  • Monroe 171667
  • Monroe 171668
  • KYB SR4060
  • KYB SR4061
  • Moog ES3529
  • Moog ES3532
  • Moog ES3531
  • Reference Number 513089
Part #: 1ASFK05008

How-to Video:

(13:19 min)