Specifications:

  • Brand New Suspension Kit
  • Comes as a 10 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacements
  • Built to strict quality control standards

California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Part Details

  • Kit Includes: (2) Front Lower Ball Joints
  • Kit Includes: (2) Front Upper Control Arms with Ball Joints
  • Kit Includes: (2) Front Outer Tie Rods
  • Kit Includes: (2) Front Sway Bar Links
  • Quantity: 10 Piece Set
  • Kit Includes: (2) Front Inner Tie Rods

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Note: When replacing steering components, it is recommended to have a professional alignment performed on the vehicle afterwards. This will ensure proper tracking and even tire wear.

  1. step : Disconnecting the Strut (1:02)
    • Pull the wire off the 18mm nut on top of the strut
    • Remove the three 18mm nuts that hold the top of the strut
  2. step : Removing the Wheel (1:44)
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the 22mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  3. step : Removing the Stabilizer Link (2:02)
    • Turn the wheel by hand or with the steering wheel
    • Apply penetrating oil to the top of the stabilizer link
    • Use a wrench on top and a socket underneath to remove the stabilizer link
    • Push down on the suspension and remove the stabilizer link
  4. step : Removing the Strut (2:39)
    • Remove two 15mm bolts from the bottom of the strut
    • Push down on the suspension, pull the strut down, and then pull it up and out
  5. step : Removing the Control Arm (3:28)
    • Apply penetrating oil to the control arm bolts
    • Use a marker to mark the control arm washer tabs for future reference
    • Loosen the 18mm nut that holds the ball joint to the steering knuckle
    • Pry on the steering knuckle with a pry bar and hit it with a hammer until it pops apart
    • Remove the 10mm bolt that holds the wiring harness clip to the control arm
    • Support the suspension with a jack
    • Remove the 21mm nuts from the control arm using a ratchet and a pipe for leverage
    • Drive the bolts out with a hammer, and a punch if necessary
    • Remove the nut from the ball joint
    • Pull out the control arm with a pry bar
  6. step : Installing the New Control Arm (6:08)
    • Install the grease-able fitting on to the new ball joint
    • Put the control arm into place and line it up
    • Start the bolts that hold the control arm to the frame by hand
    • Tap the bolts in with a hammer
    • Start the 21mm nuts by hand
    • With a wrench on each side of the bolt, realign the bolt mark with the tab mark
    • Preliminarily tighten the nuts
    • Lower the suspension using the jack
    • Thread the ball joint into the steering knuckle
    • Jack the suspension back up
    • Start the ball joint nut by hand
    • Tighten the ball joint nut
    • Tighten the control arm nuts to 100 foot-pounds of torque, making sure the marks still line up
    • Lower the suspension using the jack
    • Reinstall the 10mm bolt that holds the wiring harness clip
    • Use a grease gun to add grease to the ball joint until the boot begins to expand
  7. step : Reinstalling the Strut (9:29)
    • Reinsert the strut, with the coil spring's end on the outside
    • Lift the strut into place
    • Start threading the top strut nuts by hand
    • Insert the lower strut bolts
    • Tighten the lower strut bolts to between 70-75 foot-pounds
  8. step : Reinstalling the Stabilizer Link (10:28)
    • Lift the sway bar with a pry bar
    • Put the stabilizer link into place
    • Put the bolt through the stabilizer link
    • Tighten the stabilizer link bolt
  9. step : Reattaching the Wheel (10:43)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 110 foot-pounds in a crossing or star pattern
    • Reattach the center cap
  10. step : Reconnecting the Strut (11:09)
    • Tighten the nuts on top of the strut to between 75-80 foot-pounds of torque
    • Reattach the wire clip to the strut nut

Tools needed for replacement:

    General Tools

  • Center Punch
  • Floor Jack
  • Hammer
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Bearing Grease
  • Marker / Writing Utensil
  • Rust Penetrant

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • A Piece of Pipe (for leverage)
  • Ratchet
  • Socket Extensions
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Pry Bar

  • Sockets - Metric

  • 10mm Socket
  • 11mm Socket
  • 12mm Socket
  • 13mm Socket
  • 14mm Socket
  • 15mm Socket
  • 16mm Socket
  • 17mm Socket
  • 18mm Socket
  • 19mm Socket
  • 20mm Socket
  • 21mm Socket
  • 22mm Socket

  • Specialty Tools

  • Grease Gun

  • Wrenches - Metric

  • 18mm Wrench

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
0
0
0
0
Suspension kit
Was overall pleased with Packaging and Timely delivery. All parts arrived as ordered and had no problem with installation. Customer service was very helpful in finding the correct parts for my vehicle and helped with the completion of my order. Will be ordering from this site again
May 7, 2018
Purchased
5 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 2 questions Browse 2 questions and 5 answers
is this for 4 wheel drive suburbans?
skyler e on May 1, 2017
BEST ANSWER: I bought mine for a 4wd suburban as well, but havent installed it yet, so i can't say for 100% sure. The company said it was, so i purchased it based on their word.
Will ball joints fit cast iron lower control arms 07 sierra 4x4 new body?
Boobies on Dec 2, 2017
BEST ANSWER: Thanks for your question! This kit is only listed for models with stamped steel control arms. Thank you!

Vehicle Fit

Year Make Model Description
2007-2014Cadillac Escalade Cadillac Escalade 10 Piece Set Steering & Suspension Kit for Models with Stamped Steel Lower Control Arms
2007-2014Cadillac Escalade ESV Cadillac Escalade ESV 10 Piece Set Steering & Suspension Kit for Models with Stamped Steel Lower Control Arms
2007-2013Cadillac Escalade EXT Cadillac Escalade EXT 10 Piece Set Steering & Suspension Kit for Models with Stamped Steel Lower Control Arms
2007-2013Chevy Avalanche 1500 Chevy Avalanche 1500 10 Piece Set Steering & Suspension Kit for Models with Stamped Steel Lower Control Arms
2007Chevy Silverado 1500 Chevy Silverado 1500 New Body Style 10 Piece Set Steering & Suspension Kit for Models with Stamped Steel Lower Control Arms
2008-2013Chevy Silverado 1500 Chevy Silverado 1500 10 Piece Set Steering & Suspension Kit for Models with Stamped Steel Lower Control Arms
2007-2013Chevy Suburban 1500 Chevy Suburban 1500 10 Piece Set Steering & Suspension Kit for Models with Stamped Steel Lower Control Arms
2007-2014Chevy Tahoe Chevy Tahoe 10 Piece Set Steering & Suspension Kit for Models with Stamped Steel Lower Control Arms
2007GMC Sierra 1500 GMC Sierra 1500 New Body Style 10 Piece Set Steering & Suspension Kit for Models with Stamped Steel Lower Control Arms
2008-2013GMC Sierra 1500 GMC Sierra 1500 10 Piece Set Steering & Suspension Kit for Models with Stamped Steel Lower Control Arms
2007-2014GMC Yukon GMC Yukon 10 Piece Set Steering & Suspension Kit for Models with Stamped Steel Lower Control Arms
2007-2013GMC Yukon XL 1500 GMC Yukon XL 1500 10 Piece Set Steering & Suspension Kit for Models with Stamped Steel Lower Control Arms

This part replaces:

  • Moog K6541
  • Moog ES800223
  • Dorman 521-024
  • Dorman 521-023
  • Hollander 511-00358R
  • Hollander 511-00359L
  • Moog K700432
  • Moog K80669
  • Moog K80670
  • Moog EV800084
  • OE # 25812725
  • OE # 12475478
  • OE # 15254061
  • OE # 15254060
  • OE # 25918049
  • OE # 25812726
Part #: 1ASFK04811


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(11:35 min)