Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

Part Details

  • Quantity:   10 Piece Set
  • Kit Includes:
      (2) Tie Rod Adjusting Sleeves
      (1) Pitman Arm
      (2) Front Upper Control Arms with Ball Joints
      (2) Front Outer Tie Rods
      (1) Idler Arm
      (2) Front Inner Tie Rods

Specifications:

  • Brand New Steering & Suspension Kit
  • Comes as a Set of 10
  • Direct replacements
  • Built to strict quality control standards

 

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Item Condition: New

California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Note: When replacing steering components, it is recommended to have a professional alignment performed on the vehicle afterwards. This will ensure proper tracking and even tire wear.

  1. step : Remove the Wheel (1:59)
    • Pull off the center cap
    • Loosen the lug nuts
    • Remove the cotter pin and loosen the 35mm hub nut
    • Loosen the seven 13mm 12-point bolts that hold the axle to the front drive
    • Raise and secure the car
    • Remove the wheel
  2. step : Loosen the Torsion Bar (2:54)
    • Spray the torsion bar with spray paint and loosen the torsion bar tension bolt with an 18mm bolt
  3. step : Remove the Tie Rod (3:45)
    • Use a pair of pliers to remove the cotter pin
    • Remove the nut at the end of the tie rod
    • Use a tie rod puller to separate the tie rod
  4. step : Remove the stabilizer links (5:25)
    • Use a 9/16 wrench to secure the bottom and a 14 mm socket to unbolt the stabilizer link
    • Use a hammer and punch to remove the stabilizer link
  5. step : Pull the Axle from the CV Joint (6:52)
    • Unbolt the seven bolts, using a pry bar to keep the hub from rotating
    • Remove the hub nut using a 35 mm socket
    • Give the axle a tap with a hammer and pull the axle out
  6. step : Remove the Ball Joint (9:00)
    • Use a jack and wood plank or two to lift the control arm and relieve tension from the ball joint
    • Unbolt the the ball joint using a breaker bar and 27mm socket
    • Use a ball joint removal tool to pull the ball joint apart
    • With a ball joint press, remove the ball joint completely
    • See Part Two for reassembly

Tools needed for replacement:

    General Tools

  • Center Punch
  • Floor Jack
  • Hammer
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Block of Wood
  • Marker / Writing Utensil
  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • A Piece of Pipe (for leverage)
  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • Complete Metric Socket Set

  • Specialty Tools

  • Ball Joint Press
  • Tie Rod Puller

There are no reviews for this item.
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
1997-2002Ford Expedition Ford Expedition Rear Wheel Drive with 2.48" Bolt Pattern Idler Arm Steering & Suspension Kit 10 Piece Set
2004Ford F150 Heritage Truck Ford F150 Heritage Truck Rear Wheel Drive with 2.48" Bolt Pattern Idler Arm Steering & Suspension Kit 10 Piece Set
1997-2003Ford F150 Truck Ford F150 Truck Rear Wheel Drive with 2.48" Bolt Pattern Idler Arm Steering & Suspension Kit 10 Piece Set
1997Ford F250 Light Duty Truck Ford F250 Light Duty Truck Rear Wheel Drive Independent Front Suspension with 2.48" Bolt Pattern Idler Arm Steering & Suspension Kit 10 Piece Set
1998-1999Ford F250 Light Duty Truck Ford F250 Light Duty Truck Rear Wheel Drive with 2.48" Bolt Pattern Idler Arm Steering & Suspension Kit 10 Piece Set
2002Lincoln Blackwood Lincoln Blackwood Rear Wheel Drive with 2.48" Bolt Pattern Idler Arm Steering & Suspension Kit 10 Piece Set
1998-2002Lincoln Navigator Lincoln Navigator Rear Wheel Drive with 2.48" Bolt Pattern Idler Arm Steering & Suspension Kit 10 Piece Set
Part #: 1ASFK04639


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(13:53 min)