Specifications:

  • Brand New Steering & Suspension Kit
  • Comes as a 10 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacements
  • Built to strict quality control standards

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Part Details

  • Kit Includes: (2) Front Lower Ball Joints
  • Kit Includes: (2) Front Outer Tie Rods
  • Kit Includes: (2) Front Sway Bar Links
  • Kit Includes: (2) Rear Sway Bar Links
  • Quantity: 10 Piece Set
  • Kit Includes: (2) Front Upper Ball Joints

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

  1. step : Removing the Wheel (0:43)
    • Pry off the hub cap with a flat blade screwdriver
    • Loosen the 35mm hub nut with the vehicle on the ground
    • Loosen the lug nuts
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Outer Tie Rod (1:08)
    • Spray both ends of the outer tie rod with penetrating oil
    • Measure from the either end of the outer tie rod
    • Place a 26mm wrench on the larger nut
    • Place a 22mm wrench on the smaller nut
    • Break the 22mm nut free
    • Straighten the cotter pin with pliers and pull it through
    • Remove the nut with a 21mm socket from the wheel knuckle
    • Hit the wheel knuckle with a hammer
    • Twist off the outer tie rod
    • Remove the 22mm nut off the outer tie rod
  3. step : Installing the New Outer Tie Rod (3:08)
    • Mark where the 22mm nut was located on the old tie rod to the new tie rod
    • Screw on the nut
    • Twist the outer tie rod into place
    • Push the outer tie rod into the wheel knuckle
    • Measure and check the outer tie rod distance
    • Tighten the 21mm nut on the wheel knuckle
    • Insert and twist the cotter pin with a pair of pliers
    • Tighten the two nuts on the outer tie rod
  4. step : Reattaching the Wheel (4:33)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the hub nut
    • Torque the lug nuts to 100 ft/lbs in a crossing or star pattern
    • Torque the hub nut to 103 ft/lbs
    • Reattach the center cap

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Measuring Tape
  • Hammer
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 19mm Socket
  • 21mm Socket

  • Wrenches - Metric

  • 26mm Wrench
  • 22mm Wrench
  • 10mm Wrench

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
0
0
0
0
Do recommend this kit
Great parts for a very good price.All parts fit well,just as expected looked and fit like the originals.I don't think I could've bought any better.Only about 500 miles so far but all is good.I would buy from these people again.
June 23, 2017
Purchased
1 year ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 1 answer
Who makes these? Are these Moog or other makers?
Chris M on Mar 26, 2017
BEST ANSWER: We have a few different aftermarket companies build these parts specifically for us, as our 1A Auto house brand. They are manufactured to the same OEM specifications as the original part that came with your vehicle. These are not Moog products. If you have any further questions, please don't hesitate to ask.

Vehicle Fit

  • 2002 Chevy Trailblazer 10 Piece Set Steering & Suspension Kit for Models with 16mm Thread Tie Rods
  • 2003 Chevy Trailblazer 10 Piece Set Steering & Suspension Kit
  • 2003 Chevy Trailblazer EXT 10 Piece Set Steering & Suspension Kit
  • 2002 GMC Envoy 10 Piece Set Steering & Suspension Kit for Models with 16mm Thread Tie Rods
  • 2003 GMC Envoy 10 Piece Set Steering & Suspension Kit
  • 2003 GMC Envoy XL 10 Piece Set Steering & Suspension Kit
  • 2003 Isuzu Ascender 10 Piece Set Steering & Suspension Kit
  • 2002 Olds Bravada 10 Piece Set Steering & Suspension Kit for Models with 16mm Thread Tie Rods
  • 2003 Olds Bravada 10 Piece Set Steering & Suspension Kit

This part replaces:

  • Moog K6663
  • Moog K6664
  • Moog ES3675
  • Moog ES3676
  • Moog K6666
  • Moog K6665
  • Moog K6668
  • Moog K6667
  • OE # 26100286
  • OE # 26100287
  • OE # 22157319, 19133670, 8191336700
  • OE # 22157320
Part #: 1ASFK04550

How-to Video:

(05:20 min)