Specifications:

  • Brand New Steering & Suspension Kit
  • Comes as a Set of 6
  • Direct replacements
  • Built to strict quality control standards

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Part Details

  • Kit Includes: (2) Front Outer Tie Rods
  • Kit Includes: (2) Front Sway Bar Links
  • Quantity: 6 Piece Set
  • Kit Includes: (2) Front Strut & Spring Assemblies

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

    It's recommended to seek an alignment after finishing this repair

  1. step : Removing the Wheel (0:47)
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the 22mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Wiper Arm (1:13)
    • Pry off the wiper arm cap with a flat blade screwdriver
    • Remove the 15mm nut from the wiper arm
    • Remove the wiper arm
    • Repeat the process for the other side
  3. step : Removing the Cowl Panel (1:46)
    • Remove the four clips along the cowl panel with a flat blade screwdriver
    • Remove the ground from the cowl panel
    • Pry off the clip near the edge of the windshield
    • Pry off the adhesive pad on either end of the cowl panel
    • Pry off the clip on the driver side of the cowl panel
    • Pull up on the cowl panel to release it from its clips
    • Pull the cowl panel up and off
  4. step : Removing the Front Strut (3:06)
    • Spray the lower and higher strut bolts with rust penetrant
    • Remove the three of the upper 15mm strut bolts and leave the last one loosened
    • Pry out the clip holding the brake line to the strut with a flat blade screwdriver
    • Remove the 18mm nut from the stabilizer link
    • Pull the stabilizer link aside
    • Remove the two 24mm nuts from the bottom of the strut and knuckle
    • Pry the wiring harness off of the strut
    • Thread the 24mm nuts onto the bolts and hammer them to move the bolts
    • Jack up underneath the knuckle
    • Remove the two bolts from the knuckle
    • Pull the strut off the steering knuckle
    • Remove the last 15mm bolt from the strut
    • Remove the strut
  5. step : Disassembling the Strut (5:27)
    • Place the spring compressors on either side of the spring
    • Tighten each back and forth a little while alternating sides
    • Remove the spark plug piece from a 13/16 spark plug socket with a 90-degree pick
    • Remove the nut at the top of the strut with a 7/8 wrench and 13/16 spark plug socket
    • Pull the mount plate from the top of the strut free
    • Remove the spring
    • Pull the boot up and off
  6. step : Assembling the Strut (6:40)
    • Remove the nut from the new strut
    • Replace the boot
    • Insert the spring into its notch on the strut
    • Tighten the bolt onto the new strut
    • Loosen each of the compressors bit by bit while alternating sides
    • Repeat until the spring compressors pull free
  7. step : Inserting the Front Strut (8:35)
    • Insert the strut into place
    • Push down on the knuckle and place the strut behind it
    • Push the strut onto the knuckle
    • Insert the bolts into the bottom of the strut and knuckle
    • Hammer the bolts in and tighten them
    • Torque the bolts to 120 foot-pounds
    • Jack up the strut into place
    • Replace the upper 15mm strut bolts by hand
    • Insert the harness clip in place on the new strut
    • Insert the clip holding the brake line
    • Insert the stabilizer link in place
    • Tighten the 18mm nut to the link
  8. step : Reattaching the Wheel (10:54)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
    • Reattach the center cap
    • Tighten the three 15mm bolts at the top of the strut
    • Tighten the lug nuts to 45 foot-pounds
  9. step : Reinstalling the Cowl Panel (11:39)
    • Insert any remaining clips into the cowl panel
    • Insert the cowl panel into place
    • Insert the adhesive on either side of the panel
    • Push in the clips along the cowl panel
    • Push on the clip near the edge of the windshield
    • Push in the clip on the driver side of the cowl panel
    • Replace and tighten the ground
  10. step : Reinstalling the Wiper Arm (13:17)
    • Push the wiper arm onto the stud
    • Tighten the 15mm nut to the wiper arm
    • Replace the wiper arm cover
    • Repeat the process for the other side

Tools needed for replacement:

    General Tools

  • Pick
  • Floor Jack
  • Jack Stands

  • Ratchets & Related

  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 15mm Socket
  • 22mm Socket
  • 18mm Socket
  • 24mm Socket
  • 21mm Socket
  • 8mm Socket

  • Sockets - SAE

  • 13/16 Inch Spark Plug Socket

  • Specialty Tools

  • Strut Spring Compression Tool

  • Wrenches - Metric

  • 18mm Wrench

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
0
0
0
0
Very pleased
Got parts in a timely manner, everything was there and fit, not to mention the price. Great deal, this is where my auto parts will be purchased from here on out.
July 3, 2017
Purchased
1 year ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 2 questions Browse 2 questions and 3 answers
Who is the manufacturer of the strut assembly?
Richard H on Jul 5, 2017
BEST ANSWER: We have a few different aftermarket companies build these parts specifically for us, as our 1A Auto house brand. They are manufactured to the same OEM specifications as the original part that came with your vehicle. If you have any further questions, please don't hesitate to ask.
Why is the 6 piece set cheaper than the 4 piece set? Is there a difference in quality?
Shack on Jun 6, 2017
BEST ANSWER: There is no difference in quality, but since we are able to save on shipping with more components in a kit we offer a better price.

Vehicle Fit

Year Make Model Description
2008-2012Buick Enclave Buick Enclave Steering & Suspension Kit 6 Piece Set
2009-2012Chevy Traverse Chevy Traverse Steering & Suspension Kit 6 Piece Set
2007-2012GMC Acadia GMC Acadia Steering & Suspension Kit 6 Piece Set
2007-2010Saturn Outlook Saturn Outlook Steering & Suspension Kit 6 Piece Set

This part replaces:

  • Moog ES800286
  • OE # 20905104
  • OE # 15869897
  • Monroe 172518
  • KYB SR4206
  • Moog K750155
Part #: 1ASFK04301


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(14:06 min)