Specifications:

  • Comes as a Set of 10
    • Fits both LH (Driver Side) & RH (Passenger) Front & Rear
  • Direct replacements
  • Built to strict quality control standards

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Part Details

  • Kit Includes: (2) Front Outer Tie Rods
  • Kit Includes: (2) Rear Strut & Spring Assemblies
  • Kit Includes: (2) Front Hub Assemblies
  • Kit Includes: (2) Rear Hub Assemblies
  • Quantity: 10 Piece Set
  • Kit Includes: (2) Front Strut & Spring Assemblies

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

  1. step : Removing the Wheel (0:45)
    • Loosen the lug nut covers with a 19mm socket
    • Pull off the hub cap
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Outer Tie Rod (1:15)
    • Measure the distance from the inner tie rod boot to the outer tie rod grease fitting
    • Note this measurement
    • Hold the outer tie rod with an adjusting wrench
    • Loosen the outer tie rod nut with another adjusting wrench
    • Remove the cotter pin from the tie rod castle nut with needle nose pliers
    • Remove the 17mm castle nut
    • Strike the steering knuckle with a hammer to loosen the outer tie rod
    • Twist off the outer tie rod and its nut
  3. step : Installing the New Outer Tie Rod (2:44)
    • Twist a new nut onto the inner tie rod
    • Twist on the new outer tie rod
    • Lift the outer tie rod into the steering knuckle
    • Measure the distance from the inner tie rod boot to the outer tie rod grease fitting
    • This should be the same as the measurement noted in Step 2
    • Fasten the castle nut onto the outer tie rod end
    • Put the cotter pin into place and bend it to hold it
    • Hold the outer tie rod with an adjusting wrench
    • Tighten the outer tie rod nut with another adjusting wrench
    • Tighten the grease fitting with a 7mm wrench
    • Fill the outer tie rod bearing with grease, using a grease gun
    • Clean the tie rod bearing
  4. step : Reattaching the Wheel (4:37)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
    • Reattach the hub cap
    • Tighten the lug nut covers with a 19mm socket

Tools needed for replacement:

    General Tools

  • Hammer
  • Floor Jack
  • Jack Stands
  • Measuring Tape

  • Materials, Fluids, and Supplies

  • Cloth Rags
  • Bearing Grease

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Torque Wrench
  • Ratchet

  • Sockets - Metric

  • 19mm Socket
  • 7mm Socket
  • 17mm Socket

  • Specialty Tools

  • Grease Gun

  • Wrenches - Metric

  • 7mm Wrench

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
0
0
0
0
Good parts
I have been very pleased with every part I have ordered from 1aauto. Every part has been a exact fit and are a good qulaity part. And there prices are a great deal
May 28, 2018
Purchased
3 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
2005-2009Buick Allure Buick Allure 10 Piece Set Steering & Suspension Kit (excluding 17 or 18 Inch Wheels)
2005-2009Buick LaCrosse Buick LaCrosse 10 Piece Set Steering & Suspension Kit (excluding 17 or 18 Inch Wheels)
2000-2005Chevy Impala Chevy Impala 10 Piece Set Steering & Suspension Kit (excluding Police Package) (excluding 17 or 18 Inch Wheels)
2000-2005Chevy Monte Carlo Chevy Monte Carlo 10 Piece Set Steering & Suspension Kit

This part replaces:

  • Hollander 527-01315
  • Hollander 538-01288
  • Hollander 538-01413
  • Hollander 538-01680B
  • OE # 12413091
  • OE # 26056811
  • OE # 26086580
  • OE # 7470017
  • OE # 7470105
  • OE # 7470143
  • Monroe 181661
  • Monroe 171661
  • Monroe 271662L
  • Monroe 271662R
  • KYB SR4002
  • Moog ES3459
  • Dorman 951-016
  • Dorman 951-071
  • Hollander 527-01315A/B
  • Hollander 538-01413, 538-01288
  • Timken N/A
  • Reference Number 512237
  • Reference Number 513121
Part #: 1ASFK04272


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(05:36 min)