Specifications:

  • Brand New Steering & Suspension Kit
  • Comes as a 8 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side)
    • Fits models with 4 groove pitman arm
  • Direct replacements
  • Built to strict quality control standards

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Direct Fit

All parts are direct fit, application-specific parts with no modifications required

Rigorously Tested

Rigorously tested and made from higher quality materials than the competition. Our parts are built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

Our parts are manufactured by some of the same factories that the OEMs use.

Prepackaged for Your Convenience

Our kits have been carefully put together to include all of the parts you need to get the job done, saving you both time and money. These kits also help take the guesswork out of finding the correct part for your vehicle’s steering or suspension system, allowing you to get started on your repair project faster.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

    NOTE: After completing the procedure you will need a professional alignment

  1. step : Removing the Wheel (0:47)
    • Loosen the 22mm caps on the hubcap with the vehicle on the ground
    • Pull the hubcap free
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Upper Control Arm (1:10)
    • Mark the tab on the adjustment piece with a marker to mark the alignment
    • Remove the two 10mm bolts holding the brake line and move the brackets
    • Remove the ball joint nut with an 18mm wrench
    • Hit the wheel knuckle and control arm to break them free
    • Remove the 21mm nuts from the upper control arm bracket
    • Jack up the wheel underneath the wheel knuckle
    • Remove the upper control arm nut
    • Remove the bolts and upper control arm bracket
    • Place a nut back on and use an air hammer to knock the bolt out if it won't budge
    • Move the control arm up and down while pulling out
  3. step : Installing the Upper Control Arm (3:52)
    • Put the upper control arm into place and push the 21mm bolts in to hold it
    • Put the brackets on either side and realign them up
    • Angle the control arm down into the wheel knuckle
    • Replace the 18mm ball joint nut
    • Replace the 21mm nuts from the upper control arm bracket
    • Replace and tighten the two 10mm bolts
    • Put a grease gun into place on the end of the control arm and fill it up
  4. step : Reattaching the Wheel (6:00)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 ft/lbs in a crossing or star pattern
    • Reattach the hubcap and tighten the caps

Tools needed for replacement:

    General Tools

  • Hammer
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Marker / Writing Utensil

  • Ratchets & Related

  • Ratchet
  • Torque Wrench

  • Sockets - Metric

  • 10mm Socket
  • 21mm Socket
  • 22mm Socket

  • Specialty Tools

  • Grease Gun

  • Wrenches - Metric

  • 18mm Wrench
  • 21mm wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 5 questions Browse 5 questions and 6 answers
Are the balls joints regreaseable?
brian d on Jul 30, 2017
BEST ANSWER: These ball joints are not greaseable. They are pre-packed with grease and are sealed.
How can I tell if I have a 4grove pitman arm?
Mickey on Dec 13, 2017
BEST ANSWER: You may physically inspect the pitman arm, or you may contact a local dealership with your VIN number to obtain the OE part number or confirm the 3 or 4 groove style.
Will this fit a 2003 silverado 1500 HD 2WD?
Brian C on Aug 30, 2017
BEST ANSWER: No, this will not fit the HD model, only the light duty 1500.
Do they have the zerks grease fittings attached to them?
Johnathon P on Jul 10, 2017
BEST ANSWER: No, these are sealed units that are not serviceable.
Does this kit fit 2004 gmc yukon denali?
Mikke on Apr 20, 2017
BEST ANSWER: Yes, as long as your factory pitman arm is 4 groove.

Vehicle Fit

  • 2002-2006 Cadillac Escalade 8 Piece Set Steering & Suspension Kit for Models with 4 Groove Pitman Arm
  • 2003-2006 Cadillac Escalade ESV 8 Piece Set Steering & Suspension Kit for Models with 4 Groove Pitman Arm
  • 2002-2006 Cadillac Escalade EXT 8 Piece Set Steering & Suspension Kit for Models with 4 Groove Pitman Arm
  • 2002-2006 Chevy Avalanche 1500 8 Piece Set Steering & Suspension Kit for Models with 4 Groove Pitman Arm
  • 1999-2006 Chevy Silverado 1500 4 Wheel Drive 8 Piece Set Steering & Suspension Kit for Models with 4 Groove Pitman Arm
  • 2007 Chevy Silverado 1500 Classic 4 Wheel Drive 8 Piece Set Steering & Suspension Kit for Models with 4 Groove Pitman Arm
  • 2000-2006 Chevy Suburban 1500 8 Piece Set Steering & Suspension Kit for Models with 4 Groove Pitman Arm
  • 2000 Chevy Tahoe (excluding Z71 Models) 8 Piece Set Steering & Suspension Kit for Models with 4 Groove Pitman Arm
  • 2001-2006 Chevy Tahoe 8 Piece Set Steering & Suspension Kit for Models with 4 Groove Pitman Arm
  • 1999-2006 GMC Sierra 1500 4 Wheel Drive 8 Piece Set Steering & Suspension Kit for Models with 4 Groove Pitman Arm
  • 2007 GMC Sierra 1500 Classic 4 Wheel Drive 8 Piece Set Steering & Suspension Kit for Models with 4 Groove Pitman Arm
  • 2000 GMC Yukon (excluding Denali Models) 8 Piece Set Steering & Suspension Kit for Models with 4 Groove Pitman Arm
  • 2001-2006 GMC Yukon 8 Piece Set Steering & Suspension Kit for Models with 4 Groove Pitman Arm
  • 2000-2006 GMC Yukon XL 1500 8 Piece Set Steering & Suspension Kit for Models with 4 Groove Pitman Arm

This part replaces:

  • Dorman 520-116
  • OE # 12475478
  • OE # 15864153, 12475485, 15047200
  • OE # 19149615
  • OE # 12471379
  • Moog K80942
  • Moog K6541
  • Moog K80631
  • Moog K6534
  • Moog K6536
  • Hollander 511-01044
Part #: 1ASFK03833


How-to Video:

(07:07 min)