• Brand New Steering & Suspension Kit
  • Comes as a 12 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacement
  • Built to strict quality control standards

Our steering and suspension components are sealed for long life and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Direct Fit

All parts are direct fit, application-specific parts with no modifications required

Rigorously Tested

Rigorously tested and made from higher quality materials than the competition. Our parts are built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

Our parts are manufactured by some of the same factories that the OEMs use.

Prepackaged for Your Convenience

Our kits have been carefully put together to include all of the parts you need to get the job done, saving you both time and money. These kits also help take the guesswork out of finding the correct part for your vehicle’s steering or suspension system, allowing you to get started on your repair project faster.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:54)
    • Loosen the lug nut covers with a 19mm socket
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Stabilizer Link (1:16)
    • Turn the wheel by hand
    • Hold the upper stabilizer link stud with an 18mm wrench
    • Remove the upper nut from the stabilizer link with an 18mm socket
    • Hold the lower stabilizer link stud with an 18mm wrench
    • Remove the lower nut from the stabilizer link with an 18mm wrench
    • Pull off the stabilizer link
  3. step : Reinstalling the Stabilizer Link (2:23)
    • Push the stabilizer link into place
    • Hold the lower stabilizer link stud with an 18mm wrench
    • Fasten the lower nut onto the stabilizer link with an 18mm wrench
    • Hold the upper stabilizer link stud with an 18mm wrench
    • Fasten the upper nut onto the stabilizer link with an 18mm socket
  4. step : Reattaching the Wheel (3:34)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
    • Reattach the center cap
    • Tighten the lug nut covers with a 19mm socket

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Floor Jack

  • Ratchets & Related

  • A Piece of Pipe (for leverage)
  • Ratchet

  • Sockets - Metric

  • 19mm Socket
  • 18mm Socket

  • Wrenches - Metric

  • 18mm Wrench

4.3 / 5.0
3 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
The order I purchased Cam in a very timely fashion I was surprised they came so quickly. I received all the parts that I ordered they were of good quality and they were all the right parts I will definitely order parts from 1a auto again and I watched the videos on how to install the parts and it was very helpful.
April 6, 2018
4 weeks ago
Great Parts
Parts arrived very fast. Seem like quality parts. All parts fit perfectly EXCEPT the inner tie rod boots. This was very disappointing and a major part of this assembly. You can't go to the parts store and buy them, so I had to modify them. That made it much more susceptible to moisture getting in. That;s why only four stars.
August 26, 2017
8 months ago
Overall a good fit
Bought this kit installed all the structs and control arms myself and then I had a dealership do the tie rods, since I needed to get it aligned anyway. Everything fit perfectly from what I did. Been driving with the kit now for a month and haven't had any issues.
December 16, 2017
5 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2006-2012 Chevy Malibu 12 Piece Set Steering & Suspension Kit
  • 2004-2007 Chevy Malibu Maxx 12 Piece Set Steering & Suspension Kit
  • 2005-2010 Pontiac G6 12 Piece Set Steering & Suspension Kit
  • 2007-2009 Saturn Aura 12 Piece Set Steering & Suspension Kit

This part replaces:

  • Dorman 520-163
  • Dorman 520-164
  • Hollander 512-01416L
  • Hollander 512-01415R
  • OE # 22730775
  • OE # 22730776
  • OE # 20784686
  • OE # 22687089, 15944090
  • Monroe 182200
  • Monroe 182199
  • Monroe 172200
  • Monroe 172199
  • KYB SR4095
  • KYB SR4094
  • Moog K80252
  • Moog ES800086
  • Moog EV80988
  • Moog K620179
  • Moog K620180
  • OE # 15944072,22687091
  • Moog K6298
  • KYB SR4098
  • OE # 15944097
Part #: 1ASFK03678

How-to Video:

(04:31 min)