Part Details

  • Quantity: 8 Piece Set
  • Kit Includes:
    (2) Front Lower Ball Joints
    (2) Front Outer Tie Rods
    (2) Front Sway Bar Links
    (2) Front Inner Tie Rods

Specifications:

  • Brand New Steering & Suspension Kit
  • Comes as an 8 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacement
  • Built to strict quality control standards

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Item Condition: New

California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Note: When replacing steering components, it is recommended to have a professional alignment performed on the vehicle afterwards. This will ensure proper tracking and even tire wear.

  1. step : Removing the Wheel (0:58)
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Pull off the hub cap
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Control Arm (3:49)
    • Straighten out the ball joint cotter pin, using a pair of needle noise pliers
    • If the cotter pin is stuck, cut the head with wire cutters
    • Then tap the stuck cotter pin out with a hammer and punch
    • Apply penetrating oil to the cotter pin if necessary
    • Pull the cotter pin out with needle nose pliers
    • Loosen the 19mm ball joint nut
    • Loosen the ball joint from the wheel spindle with a pickle fork and hammer
    • Remove the 19mm nut
    • Remove the two 17mm nuts connecting the ball joint to the control arm
    • Remove the 17mm bolt connecting the ball joint to the control arm
    • Separate the ball joint from the control arm with a pry bar
  3. step : Installing the Ball Joint (9:12)
    • Thread the grease fitting onto the new ball joint by hand
    • Tighten the grease fitting with a 10mm wrench
    • Put the ball joint into the wheel spindle
    • Thread the 19mm castle nut onto the ball joint stud
    • Lower the control arm with a pry bar
    • Put the ball joint bracket studs into the control arm
    • Fasten the 17mm nuts onto the ball joint bracket
    • Insert the 17mm bolt into the ball joint bracket
    • Tighten the two 17mm nuts to 94 foot-pounds of torque
    • Tighten the 17mm bots to 94 foot-pounds
    • Tighetn the 19mm nut onto the ball joint stud
    • Make sure the castle nut lines up with the cotter pin hole
    • Insert the cotter pin sideways, with the longer leg facing in toward the center of the vehicle
    • Bend one of the cotter pin legs around the nut with pliers
  4. step : Reattaching the Wheel (11:53)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts 76 foot-pounds in a crossing or star pattern
    • Reattach the center cap

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Center Punch
  • Hammer
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers
  • Wire Cutters

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • 21mm Socket
  • 19mm Socket
  • 17mm Socket

  • Specialty Tools

  • Pickle Fork

  • Wrenches - Metric

  • 17mm Wrench
  • 19mm Wrench
  • 10mm Wrench

5.0 / 5.0
2 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
2
0
0
0
0
I like it because it come with everything you need so I will be shoping with you and I like the price it was good for what I got not to high for my car so thank for help me fixing my car if I need anything iwill be order for 1A FOR now on so thank you guy very much you will here for me if I need anything for my car so see you the next time I need something ok thank you so much
August 22, 2018
Purchased
1 month ago
Just what i needed
Perferct. Easy to install. Suspension and steering perfect. On the way to get my alignment. Thanks
January 29, 2017
Purchased
1 year ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
1997-2000Lexus ES300 Lexus ES300 8 Piece Set Steering & Suspension Kit
2001Lexus ES300 Lexus ES300 (Built Before 7/01 Production Date) 8 Piece Set Steering & Suspension Kit
1997-2003Toyota Avalon Toyota Avalon 8 Piece Set Steering & Suspension Kit
1997-2000Toyota Camry Toyota Camry 8 Piece Set Steering & Suspension Kit
2001Toyota Camry Toyota Camry (Built Before 7/01 Production Date) 8 Piece Set Steering & Suspension Kit
1999-2002Toyota Solara Toyota Solara 8 Piece Set Steering & Suspension Kit

This part replaces:

  • Moog K9499
  • Moog K90311
  • Moog K90312
  • Moog EV301
  • Moog ES3306
  • OE # 4881033010
  • OE # 4550329355
  • OE # 4881006030
  • OE # 4550339135
  • OE # 4882006030
  • OE # 4504629255
  • OE # 4333039435
Part #: 1ASFK03544


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(14:09 min)