Specifications:

  • Brand New Steering & Suspension Kit
  • Comes as a 10 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacement
  • Built to strict quality control standards

 

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Direct Fit

All parts are direct fit, application-specific parts with no modifications required

Rigorously Tested

Rigorously tested and made from higher quality materials than the competition. Our parts are built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

Our parts are manufactured by some of the same factories that the OEMs use.

Prepackaged for Your Convenience

Our kits have been carefully put together to include all of the parts you need to get the job done, saving you both time and money. These kits also help take the guesswork out of finding the correct part for your vehicle’s steering or suspension system, allowing you to get started on your repair project faster.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:44)
    • Remove the hub cap by loosening the lug nuts
    • Remove the lug nuts and tire
  2. step : Removing the Stabilizer Link (1:09)
    • Using locking pliers to clip onto the top of the stabilizer link
    • Then remove 14mm bolt from bottom of the stabilizer link
    • Remove the stabilizer link with a hammer or reciprocating saw
  3. step : Replacing the Stabilizer Link (2:07)
    • Put the stabilizer piece back into place
    • Use four washers, four grommets, and a tube
    • Use a jack stand to help push it through till it appears through the top
    • Tighten the 14mm bolt on the stabilizer link
  4. step : Replacing the Wheel (3:33)
    • Put the tire in place
    • Replace and tighten each lug nut
    • Torque each lug nut in a crossing pattern to 100 ft/lbs
    • Torque the center hub nut to 160 ft/lbs
    • Replace the hub cap and tighten the lug nut caps

Tools needed for replacement:

    General Tools

  • Sawzall
  • Jack Stands
  • Hammer

  • Pliers, Cutters & misc Wrenches

  • Vise Grip Pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench

  • Sockets - Metric

  • 22mm Socket
  • 14mm Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 2 answers
Are the upper ball joints bolt ons?
A M on Sep 16, 2016
BEST ANSWER: No you have to press them in the upper control arm. I rented the press from Advance Auto.

Vehicle Fit

  • 1999-2006 Chevy Silverado 1500 2 Wheel Drive 10 Piece Set Steering & Suspension Kit
  • 2007 Chevy Silverado 1500 Classic 2 Wheel Drive 10 Piece Set Steering & Suspension Kit
  • 1999-2006 GMC Sierra 1500 2 Wheel Drive 10 Piece Set Steering & Suspension Kit
  • 2007 GMC Sierra 1500 Classic 2 Wheel Drive 10 Piece Set Steering & Suspension Kit

This part replaces:

  • Hollander ES3492
  • OE # 12475486
  • OE # 15750786, 15015515
  • OE # 26079801
  • OE # 26076544
  • Moog K6540
  • Moog K80631
  • Moog K6539
  • Moog EV370
  • Moog ES3492T
Part #: 1ASFK03466


How-to Video:

(04:39 min)