Specifications:

  • Brand New Steering & Suspension Kit
  • Comes as a 10 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacements
  • Built to strict quality control standards

Our steering and suspension components are sealed for long life and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Direct Fit

All parts are direct fit, application-specific parts with no modifications required

Rigorously Tested

Rigorously tested and made from higher quality materials than the competition. Our parts are built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

Our parts are manufactured by some of the same factories that the OEMs use.

Prepackaged for Your Convenience

Our kits have been carefully put together to include all of the parts you need to get the job done, saving you both time and money. These kits also help take the guesswork out of finding the correct part for your vehicle’s steering or suspension system, allowing you to get started on your repair project faster.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Install the new ball joint (0:40)
    • Set up the ball joint in the ball joint press.
    • Get the top of the ball joint flush with the top of the control arm.
    • Readjust the press, taking the rubber boot off and get the control arm the rest of the way in.
    • Replace the rubber boot.
    • Lock it into place with a snap ring.
    • If you have snap ring pliers, this is much easier but you can do it without them.
  2. step : Reassemble the steering knuckle and control arm. (2:35)
    • Position the ball joint pointing outward and work the steering knuckle onto it.
    • Lower the jack stand from the control arm.
    • Thread the nut onto the ball joint.
    • Put the grease fitting on the ball joint.
  3. step : Install the axle (3:36)
    • Get the axle into the hub and transmission.
    • Torque the bolts to 60 foot pounds, using a star pattern to secure the axle evenly.
  4. step : Put the tie rod back on (4:22)
    • Torque the ball joint nut to 98 foot pounds and secure with a cotter pin.
    • Fill the lower ball joint grease fitting with grease using a grease gun.
    • Torque the tie rod nut to 60 ft lbs and secure with a cotter pin.
  5. step : Install the stabilizer link. (5:48)
    • Thread the washers and bushings onto the link.
    • Jack the control arm up and tighten the stabilizer link nuts to 15-16 ft lbs.
    • Thread the hub nut on.
    • Lower the jack from the suspension.
    • Retighten the torsion bar to the mark you made earlier.
  6. step : Put the wheel back on (7:35)
    • Thread the lug nuts on.
    • Lower the vehicle.
    • Torque the lug nuts in a star pattern to 100 ft lbs.
    • Torque the hub nut to 220 ft lbs using your 35 mm socket.
    • Put the retainer and cotter pin and wheel cap on.
    • Have your alignment checked and adjusted.

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Center Punch
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Marker / Writing Utensil

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet
  • 1/2 Inch Breaker Bar
  • A Piece of Pipe (for leverage)

  • Screwdrivers & Related

  • Phillips Head Screwdriver
  • Flat Blade Screwdriver

  • Sockets - Metric

  • Complete Metric Socket Set
  • 35mm Socket

  • Sockets - SAE

  • Complete SAE Socket Set

  • Specialty Tools

  • Grease Gun
  • Pitman Arm Puller
  • Ball Joint Press

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1997-2002 Ford Expedition 2 Wheel Drive 10 Piece Set Steering & Suspension Kit
  • 2004 Ford F150 Heritage Truck 2 Wheel Drive 10 Piece Set Steering & Suspension Kit
  • 1997-2003 Ford F150 Truck 2 Wheel Drive 10 Piece Set Steering & Suspension Kit
  • 1997-1999 Ford F250 Light Duty Truck 2 Wheel Drive 10 Piece Set Steering & Suspension Kit
  • 1998-2002 Lincoln Navigator 2 Wheel Drive 10 Piece Set Steering & Suspension Kit

This part replaces:

  • Dorman 520-218
  • Dorman 520-217
  • Hollander 511-01022BL
  • Hollander 511-01022BR
  • OE # 5L3Z 3085 B
  • OE # 5L3Z 3084 B
  • Moog K8694T, K80771
  • Moog ES3366T
  • Moog ES3367T
  • Moog ES3365T
  • Moog K8728T
  • Moog K8726T
  • Moog K8772
  • Moog ES3364
Part #: 1ASFK03422



How-to Video:

(08:42 min)