Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

Part Details

  • Bearing Type:   Ball Bearing
  • Quantity:   8 Piece Set
  • Kit Includes:
      (2) Front Outer Tie Rods
      (2) Front CV Axles
      (2) Front Wheel Bearings
      (2) Front Strut & Spring Assemblies

Specifications:

  • Brand New Steering & Suspension Kit
  • Comes as a 8 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacements
  • Built to strict quality control standards

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Item Condition: New

California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Note: When replacing steering components, it is recommended to have a professional alignment performed on the vehicle afterwards. This will ensure proper tracking and even tire wear.

  1. step : Removing the Wheel (0:40)
    • Pry off the hub cap with a flat blade screwdriver
    • Loosen the 35mm hub nut with the vehicle on the ground
    • Loosen the lug nuts in a crossing or star pattern
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Rotor (1:21)
    • Remove the 17mm bolts from the brake caliper while using an 18mm wrench to hold the inside nut
    • Pry the brake pads into the caliper with a flat blade screwdriver to push in the pistons
    • Pull the caliper aside
    • Pry the brake pads off with a flat blade screwdriver
    • Remove the 18mm bolts from the brake caliper bracket
    • Pull off the brake caliper bracket
    • Pull the rotor off
    • If the rotor will not come off hit the rotor with a ball peen hammer
    • If the rotor still won't come off, thread the bolts into the press holes and slide the rotor off
    • Remove the center hub nut
    • Hit the Axle with a hammer
  3. step : Removing the Hub (3:30)
    • Disconnect the clips on the harness on the upper control arm
    • Disconnect the wiring harness
    • Spray each side of the hub with penetrating oil
    • Remove the three 18mm bolts holding the hub
    • Hammer the back of the hub to loosen it
    • Pull the harness through and remove the hub
    • Hammer the backing plate off the hub
  4. step : Installing the New Hub (5:35)
    • Feed the harness through the backing plate
    • Place the backing plate into place
    • Push the hub onto the axle and into place
    • Place an 18mm bolt to hold the plate and hub to the wheel knuckle
    • Replace and tighten the 18mm bolts
    • Torque the 18mm bolt to 90 ft/lbs
    • Clip the wiring harness to the steering wheel knuckle
    • Connect the wiring harness
  5. step : Installing the Rotor (7:31)
    • Slide the rotor on
    • Thread on one lug nut to hold the rotor in place
    • Apply brake grease to the caliper bracket bolts
    • Put the bracket back into place
    • Start the 18mm bolts by hand and tighten them
    • Torque the bolts to 110 ft/lbs of torque
    • Install the new brake pads into the bracket
    • Apply brake grease to the brake pads
    • Put the caliper on
    • Thread the 17mm bolts by hand
    • Torque bolts to 40 ft/lbs
    • Replace the hub nut and remove the lug nut
  6. step : Reattaching the Wheel (9:16)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the hub nut
    • Torque the lug nuts to 100 ft/lbs in a crossing or star pattern
    • Torque the hub nut to 103 ft/lbs
    • Reattach the center cap
  7. step : Testing the Brakes (10:11)
    • Pump your brakes repeatedly until they feel firm
    • Test your brakes at 5 miles per hour and then 10 miles per hour
    • Road test the vehicle

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Jack Stands
  • Hammer

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Brake Parts Cleaner

  • Ratchets & Related

  • A Piece of Pipe (for leverage)
  • Torque Wrench
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 35mm Socket
  • 19mm Socket
  • 18mm Socket
  • 17mm Socket

  • Wrenches - Metric

  • 18mm Wrench

There are no reviews for this item.
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
2004-2007Buick Rainier Buick Rainier 8 Piece Set Steering & Suspension Kit
2002Chevy Trailblazer Chevy Trailblazer 8 Piece Set Steering & Suspension Kit for Models with 16mm Thread Tie Rods
2003-2009Chevy Trailblazer Chevy Trailblazer (excluding SS Models) 8 Piece Set Steering & Suspension Kit
2002Chevy Trailblazer EXT Chevy Trailblazer EXT 8 Piece Set Steering & Suspension Kit for Models with 16mm Thread Tie Rods
2003-2006Chevy Trailblazer EXT Chevy Trailblazer EXT 8 Piece Set Steering & Suspension Kit
2002GMC Envoy GMC Envoy 8 Piece Set Steering & Suspension Kit for Models with 16mm Thread Tie Rods
2003-2009GMC Envoy GMC Envoy 8 Piece Set Steering & Suspension Kit
2002GMC Envoy XL GMC Envoy XL 8 Piece Set Steering & Suspension Kit for Models with 16mm Thread Tie Rods
2003-2006GMC Envoy XL GMC Envoy XL 8 Piece Set Steering & Suspension Kit
2004-2005GMC Envoy XUV GMC Envoy XUV 8 Piece Set Steering & Suspension Kit
2003-2008Isuzu Ascender Isuzu Ascender 8 Piece Set Steering & Suspension Kit
2002Oldsmobile Bravada Olds Bravada 8 Piece Set Steering & Suspension Kit for Models with 16mm Thread Tie Rods
2003-2004Oldsmobile Bravada Olds Bravada 8 Piece Set Steering & Suspension Kit
2005-2009Saab 9-7X Saab 9-7X 8 Piece Set Steering & Suspension Kit
Part #: 1ASFK03388


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(10:42 min)