Specifications:

  • Brand New Steering & Suspension Kit
  • Comes as a 14 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacements
  • Built to strict quality control standards

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:43)
    • Pry off the hub cap with a flat blade screwdriver
    • Loosen the 35mm hub nut with the vehicle on the ground
    • Loosen the lug nuts
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Outer Tie Rod (1:08)
    • Spray both ends of the outer tie rod with penetrating oil
    • Measure from the either end of the outer tie rod
    • Place a 26mm wrench on the larger nut
    • Place a 22mm wrench on the smaller nut
    • Break the 22mm nut free
    • Straighten the cotter pin with pliers and pull it through
    • Remove the nut with a 21mm socket from the wheel knuckle
    • Hit the wheel knuckle with a hammer
    • Twist off the outer tie rod
    • Remove the 22mm nut off the outer tie rod
  3. step : Installing the New Outer Tie Rod (3:08)
    • Mark where the 22mm nut was located on the old tie rod to the new tie rod
    • Screw on the nut
    • Twist the outer tie rod into place
    • Push the outer tie rod into the wheel knuckle
    • Measure and check the outer tie rod distance
    • Tighten the 21mm nut on the wheel knuckle
    • Insert and twist the cotter pin with a pair of pliers
    • Tighten the two nuts on the outer tie rod
  4. step : Reattaching the Wheel (4:33)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the hub nut
    • Torque the lug nuts to 100 ft/lbs in a crossing or star pattern
    • Torque the hub nut to 103 ft/lbs
    • Reattach the center cap

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Measuring Tape
  • Hammer
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 19mm Socket
  • 21mm Socket

  • Wrenches - Metric

  • 26mm Wrench
  • 22mm Wrench
  • 10mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 2 questions Browse 2 questions and 5 answers
Do I have to grease these or are they pre greased?
Sean K on Dec 7, 2017
BEST ANSWER: Some components come sealed, (no grease). Others in the kit do have zerk(grease fitting) you must put on and grease using a grease gun. I don't recall which pieces exactly though.
What brand makes this kit? Do u have a kit with a longer warranty?
Frank L on Apr 9, 2017
BEST ANSWER: We have a few different aftermarket companies build these parts specifically for us, as our 1A Auto house brand. They are manufactured to the same OEM specifications as the original part that came with your vehicle. These parts have a lifetime warranty, and we do not have another kit with a better warranty. If you have any further questions, please don't hesitate to ask.

How-to Video:

(05:20 min)

Tools List:

    General Tools

  • Floor Jack
  • Measuring Tape
  • Hammer
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 19mm Socket
  • 21mm Socket

  • Wrenches - Metric

  • 26mm Wrench
  • 22mm Wrench
  • 10mm Wrench



This part replaces:

  • Dorman 520-143
  • Dorman 520-144
  • Hollander 511-01054R
  • Hollander 511-01055L
  • OE # 26100286
  • OE # 26100287
  • OE # 22157319, 19133670, 8191336700
  • OE # 22157320
  • OE # 26100288
  • OE # 15858683
  • OE # 15858682
  • Moog K6663
  • Moog K6664
  • Moog ES3675
  • Moog ES3676
  • Moog K80824
  • Moog K80825
  • Moog EV80965
  • Moog K6668
  • Moog K6667
  • Moog K640293
  • Moog K640294

Vehicle Fit

  • 2004-2007 Buick Rainier 14 Piece Set Steering & Suspension Kit
  • 2004-2007 Chevy Trailblazer 14 Piece Set Steering & Suspension Kit
  • 2004-2006 Chevy Trailblazer EXT 14 Piece Set Steering & Suspension Kit
  • 2003-2009 GMC Envoy 14 Piece Set Steering & Suspension Kit
  • 2004 GMC Envoy XL 14 Piece Set Steering & Suspension Kit
  • 2004-2008 Isuzu Ascender 14 Piece Set Steering & Suspension Kit
  • 2004 Olds Bravada 14 Piece Set Steering & Suspension Kit
  • 2005-2007 Saab 9-7X 14 Piece Set Steering & Suspension Kit
Part #: 1ASFK03386

Ships Same Day for orders placed by 4 P.M. ET

We're here to help

1A Auto Parts

Customer Feedback

"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More