Replaces
Steering & Suspension Kit - 1ASFK03319
1ASFK03319Specifications:
- Brand New Steering & Suspension Kit
- Comes as a 4 Piece Kit
- Fits LH (Driver Side) & RH (Passenger Side)
- Fits LH (Driver Side) & RH (Passenger Side)
- Direct replacements
- Built to strict quality control standards
Our steering and suspension components are sealed for long life and do not require the extra maintenance typically required by greasable versions.
Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards. Failure to do so may result in issues with steering and premature tire wear.
Direct FitAll parts are direct fit, application-specific parts with no modifications required
Rigorously TestedRigorously tested and made from higher quality materials than the competition. Our parts are built to have a longer life in any environment or road conditions.
State of the Art ManufacturingOur parts are manufactured by some of the same factories that the OEMs use.
Prepackaged for Your ConvenienceOur kits have been carefully put together to include all of the parts you need to get the job done, saving you both time and money. These kits also help take the guesswork out of finding the correct part for your vehicle’s steering or suspension system, allowing you to get started on your repair project faster.
Lifetime Warranty
This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.
-
step : Removing the Wheel (0:47)
- Loosen the lug nuts
- Raise and support the vehicle
- Remove the lug nuts
- Pull off the wheel
-
step : Removing the Outer Tie Rod (1:14)
- Soak the tie rod jam nut and the other tie rod nut in rust penetrant
- Loosen the jam nut with a 24mm wrench
- Remove the 21mm nut from the outer tie rod
- Strike the wheel spindle with a hammer to release the outer tie rod
- Pull the tie rod down out of the wheel spindle
- Twist off the tie rod, counting how many turns it takes to remove
- Hold the inner tie rod with locking pliers
- Mark the jam nut position with a marker
- Twist off the jam nut with a 24mm wrench, counting how many turns it takes to remove
-
step : Installing the Outer Tie Rod (5:25)
- Mark the new jam nut
- Twist on the new jam nut the same number of turns it took to remove the old one
- Twist on the outer tie rod the same number of turns it took to remove the old one
- Insert the outer tie rod stud into the wheel spindle
- Fasten the 22mm nut onto the outer tie rod
- Tighten the 22mm nut to 63 foot-pounds of torque
- Tighten the new jam nut with a 22mm wrench
- Grease the tie rod fitting until the boot swells
-
step : Installing the Wheel (7:04)
- Lift the wheel into place
- Start the lug nuts
- Lower the vehicle to the ground
- Tighten the lug nuts to 110 foot-pounds
Tools needed for replacement:
- Jack Stands
- Hammer
- Floor Jack
- Gloves
- Rust Penetrant
- Marker / Writing Utensil
- Vise Grip Pliers
- Side Cutters
- Ratchet
- Torque Wrench
- Socket Extensions
- 1/2 Inch Breaker Bar
- Complete Metric Socket Set
General Tools
Materials, Fluids, and Supplies
Pliers, Cutters & misc Wrenches
Ratchets & Related
Sockets - Metric
Vehicle Fit
- 2005-2010 Chrysler 300 4 Piece Set Steering & Suspension Kit Rear Wheel Drive
- 2008-2010 Dodge Challenger 4 Piece Set Steering & Suspension Kit
- 2006-2010 Dodge Charger 4 Piece Set Steering & Suspension Kit Rear Wheel Drive
- 2005-2008 Dodge Magnum 4 Piece Set Steering & Suspension Kit Rear Wheel Drive
This part replaces:
- Hollander 538-01735
- OE # 52013468AC, 52106710AC
- OE # 4779199AA
- Moog ES3571