Part Details

  • Quantity: 8 Piece Set
  • Kit Includes:
    (2) Front Lower Ball Joints
    (1) Pitman Arm
    (2) Front Sway Bar Links
    (2) Front Upper Ball Joints
    (1) Idler Arm


  • Brand New Steering & Suspension Kit
  • Comes as an 8 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacements
  • Built to strict quality control standards

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Item Condition: New

WARNING: Cancer and Reproductive Harm -

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Note: When replacing steering components, it is recommended to have a professional alignment performed on the vehicle afterwards. This will ensure proper tracking and even tire wear.

  1. step : Loosening the Lug Nuts and Hub Nut (1:17)
    • Before lifting the car, loosen the lug nuts up with a 19 mm wrench, and the hub nut using a 35 mm socket. It's best to do this while the car is on the ground so the wheels won't move.
  2. step : Raising and Securing the Car (1:50)
    • Position the jack under the control arm with a jack stand under the frame.
    • Raise the car (most of the weight should be on the jack stand).
  3. step : Removing the Brake Caliper (2:04)
    • Remove the tire, and the hub nut and washer.
    • To remove the break caliper, there are two 18 mm bolts to remove-one on top and one on the lower backside.
    • Once those are off, pry the caliper right off with the wrench.
    • Remove the brake rotor.
  4. step : Redistributing the Weight (3:20)
    • Now, to redistribute the weight, move the jack out to the end of the control arm, and jack it up so that most of the weight in now on the jack with only a little weight on the jack stand.
  5. step : Removing the Harness (3:43)
    • First, disconnect the harness. Remove the clips on the left side of the harness, and use a screwdriver to pry it up off the frame.
    • It would be best to coat the nuts with penetrating oil at this time.
    • Take the small bolt off with the 10 mm wrench (put the bolt and the nut back into the control arm just for safe keeping so you'll know where they are).
    • Remove the last bolt on the frame-a 13 mm bolt.
    • Once the bolts are removed, pull the harness out and free. (Save the clips from the harness in case you need them to install)
  6. step : Removing the Hub (5:24)
    • There's three 18 mm bolts that hold the hub-one in the back, one in the middle of the top, and one in the front.
    • The front and rear ones can be reached with an impact wrench or regular wrench. The middle one, you'll need to use a hand wrench. (Swivel the steering to help you get at the bolt easier.)
    • Remove all three bolts.
    • Using the pry bar or screwdriver, pry against the steering knuckle. (Be careful not to bend up that backing plate too much.)
    • Pull out and away from the backing plate, and the hub is out.
    • (There is a little O ring that needs to be replaced correctly. If you are replacing the hub, transfer it to the new hub. If not, make sure it's in the correct spot.)
  7. step : Removing the Jounce Bumper (7:13)
    • There are two bolts where the ball joint is secured to the control arm. (If your ball joint hasn't been replaced before, you'll just see little round rivets.)
    • If it is rivets, use a cold chisel and pound them to shear them right off.
    • Remove these bolts or rivets on the front, in the back and underneath.
  8. step : Removing the Ball Joint (7:50)
    • Remove the cotter pin and the bolt-22 mm or 24 mm-from the ball joint.
    • Remove the cotter pin and the bolt-18 mm or 19 mm-from the tire rod end.
    • For the tire rod end, hit it with a couple of good hammer hits. Holding the control arm, give the ball joint a few whacks as well.
    • Take out all the bolts from the top of the ball joint.
    • Pull down on the control arm and towards the rear of the vehicle, and the ball joint will come out.

Tools needed for replacement:

    Air Powered Tools

  • Air Chisel

  • General Tools

  • Floor Jack
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Ratchets & Related

  • Socket Extensions
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Pry Bar

  • Sockets - Metric

  • Complete Metric Socket Set

  • Wrenches - Metric

  • 10mm Wrench
  • 11mm Wrench
  • 12mm Wrench
  • 13mm Wrench
  • 14mm Wrench
  • 15mm Wrench
  • 16mm Wrench
  • 17mm Wrench
  • 18mm Wrench
  • 19mm Wrench

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
Highly recommend this product and will use this company again
July 3, 2017
1 year ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 2 answers
Who makes these parts?
Jeff H on Apr 27, 2017
BEST ANSWER: These are made by multiple vendors based in Taiwan or China. We label them as our 1A Auto brand and back them with a limited lifetime warranty.

Vehicle Fit

Year Make Model Description
1997-2005Chevy Blazer S10 Chevy Blazer S10 4 Wheel Drive 8 Piece Set Steering & Suspension Kit
1997-2004Chevy S10 Pickup Chevy S10 Pickup 4 Wheel Drive 8 Piece Set Steering & Suspension Kit
1997-2001GMC Jimmy S-15 GMC Jimmy S-15 4 Wheel Drive 8 Piece Set Steering & Suspension Kit
1997-2004GMC S-15 Sonoma GMC S-15 Sonoma 4 Wheel Drive 8 Piece Set Steering & Suspension Kit
1998-2000Isuzu Hombre Isuzu Hombre 4 Wheel Drive 8 Piece Set Steering & Suspension Kit
1997-2001Oldsmobile Bravada Olds Bravada 4 Wheel Drive 8 Piece Set Steering & Suspension Kit

This part replaces:

  • Moog K5335
  • Moog K6251
  • Moog K5320
  • Moog K6600
  • Moog K6255
  • OE # 26054968
Part #: 1ASFK03232

Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(09:59 min)