Specifications:

  • Brand New Steering & Suspension Kit
  • Comes as a 12 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacements
  • Built to strict quality control standards

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

An adjustable ball joint will look slightly different than a standard, non-adjustable version.  The stud will be offset once installed and can be rotated in order to allow a greater range of vehicle suspension alignment.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Part Details

  • Kit Includes: (2) Front Lower Ball Joints
  • Kit Includes: (2) Front Outer Tie Rods
  • Quantity: 12 Piece Set
  • Kit Includes: (2) Front Sway Bar Links
  • Kit Includes: (2) Steering Rack & Pinion Bellows
  • Kit Includes: (2) Front Upper Ball Joints
  • Kit Includes: (2) Front Inner Tie Rods

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

  1. step : Remove the wheels (1:00)
    • Loosen the lug nuts
    • Raise and secure the vehicle
    • Remove the wheel
  2. step : Remove the tie rod (1:32)
    • Mark the alignment on the tie rod with a sharpie.
    • Use two wrenches to loosen up the tie rod nut.
    • Remove the cotter pin and remove the 16 mm nut.
    • Use a tie rod puller to pry out the tie rod.
    • Unscrew the tie rod.
  3. step : Install the new tie rod (4:05)
    • Adjust the new locking nut to the same spot that the old one was (where you made your mark)
    • Screw in the new tie rod.
    • Install the cotter pin and bolt on the 17mm nut.
    • Install the cotterpin.
    • Use a grease gun to fill the joint.
  4. step : Replace the wheel (7:15)
    • Put the wheel on and hand tighten the lug nuts
    • Lower the car and torque the lug nuts to 80 ft lbs.

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Marker / Writing Utensil

  • Pliers, Cutters & misc Wrenches

  • Adjustable Wrench
  • Needle nose pliers

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Torque Wrench

  • Sockets - Metric

  • 16mm Socket
  • 17mm Socket
  • 18mm Socket
  • 19mm Socket

  • Specialty Tools

  • Grease Gun
  • Tie Rod Puller

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1997-1999 Acura CL 12 Piece Set Steering & Suspension Kit
  • 1994-1997 Honda Accord 12 Piece Set Steering & Suspension Kit
  • 1995-1997 Honda Odyssey 12 Piece Set Steering & Suspension Kit
  • 1996-1997 Isuzu Oasis 12 Piece Set Steering & Suspension Kit

This part replaces:

  • Beck Arnley 103-2876
  • Beck Arnley 103-2865
  • OE # 53560-SV4-013
  • OE # 53540-SV4-013
  • OE # 53010-SV4-000
  • OE # 51220S84A01,51220S84A02, 51220SM1A01,51220SM1A02
  • OE # 53534SL4J01, 53535SL5A01
  • OE # 53534S30003, 53534SV4003
  • OE # 51314SM4020
  • Moog ES3391R
  • Moog ES3392R
  • Moog K9643
  • Moog K90122
  • Moog EV342
  • Moog K90490
  • OE # 51220S84A01, 51220S84A02, 51220SM1A01, 51220SM1A02
Part #: 1ASFK02977

How-to Video:

(08:20 min)