Specifications:

  • Brand New Steering & Suspension Kit
  • Comes as a 14 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacements
  • Built to strict quality control standards

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Remove the Wheel (1:59)
    • Pull off the center cap
    • Loosen the lug nuts
    • Remove the cotter pin and loosen the 35mm hub nut
    • Loosen the seven 13mm 12-point bolts that hold the axle to the front drive
    • Raise and secure the car
    • Remove the wheel
  2. step : Loosen the Torsion Bar (2:54)
    • Spray the torsion bar with spray paint and loosen the torsion bar tension bolt with an 18mm bolt
  3. step : Remove the Tie Rod (3:45)
    • Use a pair of pliers to remove the cotter pin
    • Remove the nut at the end of the tie rod
    • Use a tie rod puller to separate the tie rod
  4. step : Remove the stabilizer links (5:25)
    • Use a 9/16 wrench to secure the bottom and a 14 mm socket to unbolt the stabilizer link
    • Use a hammer and punch to remove the stabilizer link
  5. step : Pull the Axle from the CV Joint (6:52)
    • Unbolt the seven bolts, using a pry bar to keep the hub from rotating
    • Remove the hub nut using a 35 mm socket
    • Give the axle a tap with a hammer and pull the axle out
  6. step : Remove the Ball Joint (9:00)
    • Use a jack and wood plank or two to lift the control arm and relieve tension from the ball joint
    • Unbolt the the ball joint using a breaker bar and 27mm socket
    • Use a ball joint removal tool to pull the ball joint apart
    • With a ball joint press, remove the ball joint completely
    • See Part Two for reassembly

Tools needed for replacement:

    General Tools

  • Center Punch
  • Floor Jack
  • Hammer
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Block of Wood
  • Marker / Writing Utensil
  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • A Piece of Pipe (for leverage)
  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • Complete Metric Socket Set

  • Specialty Tools

  • Ball Joint Press
  • Tie Rod Puller

4.7 / 5.0
3 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
2
1
0
0
0
Good looking
Damn good kit everything works fine on and off off and on simple as pie
January 26, 2018
Purchased
1 month ago
Easy way to replace front end parts in an F1 50!
One AAA auto website was very easy to use to order the parts to customer service asking questions and the availability of videos to show you how to change the parts and eliminate questions on how to replace your front end parts. Parts were of quality workmanship and very easy to install and replace. I got my order three days by UPS. I recommend one AA auto to anybody thank you
February 8, 2018
Purchased
3 weeks ago
good bang for your buck
pretty decent quality. items did not feel cheap everything was in order only negative comment was my tie rod’s thread was damaged and was not able to get the nut on but i used a tap and tie and got it to go in other then that, good stuff
February 5, 2018
Purchased
3 weeks ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

How-to Video:

(13:53 min)

Tools List:

    General Tools

  • Center Punch
  • Floor Jack
  • Hammer
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Block of Wood
  • Marker / Writing Utensil
  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • A Piece of Pipe (for leverage)
  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • Complete Metric Socket Set

  • Specialty Tools

  • Ball Joint Press
  • Tie Rod Puller



This part replaces:

  • Dorman 520-218
  • Dorman 520-217
  • Hollander 511-01022BL
  • Hollander 511-01022BR
  • Moog K8695T
  • OE # 5L3Z3085B
  • OE # 5L3Z3084B
  • OE # F65Z3281BA, F65Z3281AA
  • OE # 1L3Z3350AB
  • Moog K8694T, K80771
  • Moog K8739T
  • Moog K8700
  • Moog ES3366T
  • Moog ES3367T
  • Moog ES3365T
  • Moog K8728T
  • Moog K8726T
  • Moog K8772
  • Moog ES3368S
  • Moog ES3364
  • OE # 5L3Z 3085 B
  • OE # 5L3Z 3084 B

Vehicle Fit

  • 1997-2002 Ford Expedition 2 Wheel Drive 14 Piece Set Steering & Suspension Kit for Models with 2.48" Bolt Pattern Idler Arm
  • 2004 Ford F150 Heritage Truck 2 Wheel Drive 14 Piece Set Steering & Suspension Kit for Models with 2.48" Bolt Pattern Idler Arm
  • 1997-2003 Ford F150 Truck 2 Wheel Drive 14 Piece Set Steering & Suspension Kit for Models with 2.48" Bolt Pattern Idler Arm
  • 1998-2002 Lincoln Navigator 2 Wheel Drive 14 Piece Set Steering & Suspension Kit for Models with 2.48" Bolt Pattern Idler Arm
Part #: 1ASFK02859

Ships Same Day for orders placed by 4 P.M. ET

We're here to help

1A Auto Parts

Customer Feedback

"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More