Specifications:

  • Brand New Suspension & Steering Kit
  • Comes as a Set of 12
  • Fits LH (Driver Side) & RH (Passenger Side) Front
  • Direct replacements
  • Built to strict quality control standards

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Part Details

  • Kit Includes: (2) Front Lower Ball Joints
  • Kit Includes: (2) Front Upper Control Arms with Ball Joints
  • Kit Includes: (2) Front Outer Tie Rods
  • Kit Includes: (2) Front Sway Bar Links
  • Kit Includes: (2) Steering Rack & Pinion Bellows
  • Kit Includes: (2) Front Inner Tie Rods
  • Quantity: 12 Piece Set

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

  1. step : Removing the Wheel (0:41)
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Outer Tie Rod (1:13)
    • Turn the wheel by hand
    • Remove the 21mm nut from the outer tie rod
    • Thread the 21mm nut on a couple of turns
    • Hold the tie rod with an adjustable wrench
    • Loosen the tie rod adjusting nut with an adjustable wrench
    • Strike the steering knuckle with a hammer
    • Twist the 21mm nut off the tie rod
    • Measure the distance from the tie rod boot to the outer tie rod stud
    • Note that measurement
    • Twist off the outer tie rod.
  3. step : Installing the Tie Rod (2:11)
    • Twist on the outer tie rod
    • Measure the distance from the tie rod boot to the outer tie rod stud
    • This should be the same as the distance noted in Step 2
    • Move the adjusting nut as necessary
    • Push the tie rod into the wheel knuckle
    • Fasten the 21mm nut onto the tie rod
    • Tighten the 21mm nut to 111 foot-pounds of torque
    • Tighten the adjusting nut
    • Twist the grease fitting into the tie rod
    • Tighten the grease fitting with a 7mm socket and ratchet
    • Add grease to the grease fitting with a grease gun
  4. step : Reattaching the Wheel (3:34)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 120 foot-pounds in a crossing or star pattern
    • Reattach the center cap

Tools needed for replacement:

    General Tools

  • Measuring Tape
  • Floor Jack
  • Hammer
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Bearing Grease

  • Pliers, Cutters & misc Wrenches

  • Adjustable Wrench

  • Ratchets & Related

  • Ratchet
  • Torque Wrench

  • Sockets - Metric

  • 21mm Socket
  • 7mm Socket
  • 10mm Socket

  • Specialty Tools

  • Grease Gun

  • Wrenches - Metric

  • 21mm wrench

4.5 / 5.0
4 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
2
2
0
0
0
a+
Shipping was very quick,all parts fit and were in great condition
July 13, 2018
Purchased
3 weeks ago
Not to bad
For what the kit is priced at I am happy with the parts. They are clearly not top of the line but that wasn’t what I was wanting to spend money on for a 250,000 miles truck. The parts came somewhat well packed and undamaged.
Install wasn’t to bad and the parts fit very well. Really wish 1A had a video compiled for this but I made do searching through different parts.
April 9, 2018
Purchased
4 months ago
Fast delivery
It showed up faster then expected and good quality parts. Thank you
September 27, 2017
Purchased
10 months ago
Good Kit over all....
This kit was great but didn't work for my truck over all. Ball joints would press out so I had to purchase a whole lower control arm and install that. The inner tie rods were not a match and couldn't use. The sway arm joints were broken when I received it and didn't work on my truck. I put the old ones back on with no issues. Over all only used the outer tie rods, upper control arm. The rest is didn't work. Good idea but just a few bad parts mixed in the bunch. Not exchanging them bc truck is back together and aligned.
August 28, 2017
Purchased
11 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2005 Ford F150 Truck 4 Wheel Drive 12 Piece Set Steering & Suspension Kit (Built After 11/04 Production Date)
  • 2006-2008 Ford F150 Truck 4 Wheel Drive 12 Piece Set Steering & Suspension Kit
  • 2006-2008 Lincoln Mark LT 4 Wheel Drive 12 Piece Set Steering & Suspension Kit

This part replaces:

  • Dorman 520-285
  • Dorman 520-286
  • Hollander 511-01089L
  • Hollander 511-01087R
  • Moog K80338
  • Moog K150283
  • OE # 4L3Z3A130CA
  • OE # 4L3Z3280DA, 4L3Z3280CA
  • OE # 2L1Z3050A
  • OE # 5L3Z5K483DA
  • OE # 6L3Z3085AL
  • OE # 6L3Z3084AR
  • OE # 4L3Z3K661FA, 4L3Z3K661EA
  • Moog K80149
  • Moog K80306
  • Moog K80308
  • Moog ES3691
  • Moog EV463
Part #: 1ASFK02637

How-to Video:

(04:25 min)