Specifications:

  • Brand New Steering & Suspension Kit
  • Comes as a 8 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side) Front
  • Direct replacements
  • Built to strict quality control standards

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Part Details

  • Kit Includes: (2) Front Outer Tie Rods
  • Kit Includes: (2) Front Sway Bar Links
  • Kit Includes: (2) Front Upper Ball Joints
  • Kit Includes: (2) Front Inner Tie Rods
  • Quantity: 8 Piece Set

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

    It is recommended to receive a professional alignment after completing this repair

  1. step : Removing the Wheel (0:43)
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Outer Tie Rod (1:05)
    • Use a pair of pliers to straighten the cotter pin and remove it
    • Remove the castle nut with an adjustable wrench
    • Measure the distance from the inner tie rod to the outer tie rod
    • Loosen the nut between the inner and outer tie rod
    • Hammer the knuckle to loosen the outer tie rod
    • Remove the outer tie rod and twist it off the inner tie rod
  3. step : Installing the Outer Tie Rod (2:05)
    • Twist the grease filler into the new outer tie rod
    • Twist the outer tie rod to the inner tie rod
    • Measure the distance and make sure it matches the recorded distance
    • Tighten the nut between the inner and outer tie rod
    • Insert the outer tie rod to the knuckle
    • Replace and tighten the castle nut while lining up the cotter pin hole
    • Insert the cotter pin and twist the ends with a pair of pliers
    • Fill up the grease filler with a grease gun
  4. step : Reattaching the Wheel (3:21)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    General Tools

  • Hammer
  • Measuring Tape
  • Floor Jack
  • Jack Stands

  • Pliers, Cutters & misc Wrenches

  • Adjustable Wrench
  • Needle nose pliers

  • Specialty Tools

  • Grease Gun

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
1995-2000Chrysler Cirrus Chrysler Cirrus 8 Piece Set Steering & Suspension Kit
1996-2000Chrysler Sebring Chrysler Sebring Convertible 8 Piece Set Steering & Suspension Kit
1995-2000Dodge Stratus Dodge Stratus 8 Piece Set Steering & Suspension Kit
1996-2000Plymouth Breeze Plymouth Breeze 8 Piece Set Steering & Suspension Kit

This part replaces:

  • OE # 4695626
  • OE # 4616570
  • Moog K7306
  • Moog ES80361
  • Moog ES80360
  • Moog EV323
  • Moog K7218
Part #: 1ASFK02625


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(03:52 min)