Specifications:

  • Brand New Steering and Suspension Kit
  • Comes as a 10 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side) Front
  • Direct replacements
  • Built to strict quality control standards

Our steering and suspension components are sealed for long life and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Direct Fit

All parts are direct fit, application-specific parts with no modifications required

Rigorously Tested

Rigorously tested and made from higher quality materials than the competition. Our parts are built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

Our parts are manufactured by some of the same factories that the OEMs use.

Prepackaged for Your Convenience

Our kits have been carefully put together to include all of the parts you need to get the job done, saving you both time and money. These kits also help take the guesswork out of finding the correct part for your vehicle’s steering or suspension system, allowing you to get started on your repair project faster.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Remove the Wheel (1:59)
    • Pull off the center cap
    • Loosen the lug nuts
    • Remove the cotter pin and loosen the 35mm hub nut
    • Loosen the seven 13mm 12-point bolts that hold the axle to the front drive
    • Raise and secure the car
    • Remove the wheel
  2. step : Loosen the Torsion Bar (2:54)
    • Spray the torsion bar with spray paint and loosen the torsion bar tension bolt with an 18mm bolt
  3. step : Remove the Tie Rod (3:45)
    • Use a pair of pliers to remove the cotter pin
    • Remove the nut at the end of the tie rod
    • Use a tie rod puller to separate the tie rod
  4. step : Remove the stabilizer links (5:25)
    • Use a 9/16 wrench to secure the bottom and a 14 mm socket to unbolt the stabilizer link
    • Use a hammer and punch to remove the stabilizer link
  5. step : Pull the Axle from the CV Joint (6:52)
    • Unbolt the seven bolts, using a pry bar to keep the hub from rotating
    • Remove the hub nut using a 35 mm socket
    • Give the axle a tap with a hammer and pull the axle out
  6. step : Remove the Ball Joint (9:00)
    • Use a jack and wood plank or two to lift the control arm and relieve tension from the ball joint
    • Unbolt the the ball joint using a breaker bar and 27mm socket
    • Use a ball joint removal tool to pull the ball joint apart
    • With a ball joint press, remove the ball joint completely
    • See Part Two for reassembly

Tools needed for replacement:

    General Tools

  • Center Punch
  • Floor Jack
  • Hammer
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Block of Wood
  • Marker / Writing Utensil
  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • A Piece of Pipe (for leverage)
  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • Complete Metric Socket Set

  • Specialty Tools

  • Ball Joint Press
  • Tie Rod Puller

4.0 / 5.0
5 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
2
1
2
0
0
Perfect
They are the best! Good quality parts right at your door super fast! Good quality people ready to help
December 29, 2017
Purchased
8 months ago
Front Suspension Kit for 2003 Ford Ranger with 2wd and Torsion Bars
The kit was complete, relatively easy to install and gave my suspension a new-like feel.
July 30, 2017
Purchased
9 months ago
Good product for the price point. Flawless transaction.
Wouldve been cooler if anything had grease fittings instead of being sealed. However, id buy again if i was in a non performance application, no questions.
December 17, 2017
Purchased
4 months ago
All but one...
The price was right for the kit, but one of the outer tie rods had to be replaced at a local parts store. It was obviously loose when I installed it - could be moved by hand - easily.
April 18, 2018
Purchased
3 weeks ago
All good except........
All parts except the inner tie rod ends were correct and fit perfectly. Your inner tie rods were the wrong part for my vehicle, found that out while I had the car up and taken apart so I had no choice but to run to the local parts store for correct parts and added cost.
October 14, 2017
Purchased
6 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 3 questions Browse 3 questions and 8 answers
Is this for a 1998 ford ranger 4x4?
mathew g on Jul 7, 2017
BEST ANSWER: Sorry Matt I'm not sure I have a 2000 Ford Explorer. I no these parts did work on a Ranger but not sure of the year . Good luck
for sport ? cause i know some are not.
destiny c on Feb 8, 2017
BEST ANSWER: I put mine on a 2000 Ford Explorer SLT. It's a base model 4 dr. I'm not sure if the Sport Model is the same, you'd need to take a look under the vehicle. This is not for a 4wd though. I purchased this kit, and a set of shocks, and that pretty much rebuilt the entire front end suspension.
Will this fit on a 21001 Ford Explorer xlt awd? Would like to know which suspension control arm kit would fit best?
Kennethia R on Jun 12, 2017
BEST ANSWER: This kit will be correct for your 2001 Explorer as long as you have the 2-piece design passenger side control arm. This kit includes the outer RH control arm.

Vehicle Fit

  • 1998-2001 Ford Explorer 10 Piece Set Steering & Suspension Kit for Models with 2 Piece Passenger Side Upper Control Arm
  • 1998-2011 Ford Ranger 10 Piece Set Steering & Suspension Kit for Models with 2 Piece Passenger Side Upper Control Arm Front Torsion Bar Suspension
  • 2001-2009 Mazda B2300 Truck 10 Piece Set Steering & Suspension Kit for Models with 2 Piece Passenger Side Upper Control Arm Front Torsion Bar Suspension
  • 1998-2001 Mazda B2500 Truck 10 Piece Set Steering & Suspension Kit for Models with 2 Piece Passenger Side Upper Control Arm Front Torsion Bar Suspension
  • 1998-2007 Mazda B3000 Truck 10 Piece Set Steering & Suspension Kit for Models with 2 Piece Passenger Side Upper Control Arm Front Torsion Bar Suspension
  • 1998-2007 Mazda B4000 Truck 10 Piece Set Steering & Suspension Kit for Models with 2 Piece Passenger Side Upper Control Arm Front Torsion Bar Suspension
  • 1998-2001 Mercury Mountaineer 10 Piece Set Steering & Suspension Kit for Models with 2 Piece Passenger Side Upper Control Arm

This part replaces:

  • Dorman 520-299
  • Hollander 511-01057AL
  • Hollander 511-01056AR
  • OE # F7ZZ3082CA
  • Moog K8694T, K80771
  • Moog EV317
  • Moog ES3461
  • Moog K7275
  • Moog K8708T
  • Moog K8710T
  • Dorman 520-221
Part #: 1ASFK02616



How-to Video:

(13:53 min)